DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Electrical and Wiring > External Lighting Goes South...





Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old 06-01-2007, 08:27 AM  
ch1466
Junior Member
 
Join Date: Jun 2007
Posts: 1
Default External Lighting Goes South...

Greetings All, New Poster.

Got a problem with an exterior light fixture that the window repair guys knocked off the wall. Found a replacement, did exactly as was suggested in the instructions and now nothing works.

Including most of the living room electronics (No TV, Lights etc.).

The breaker is 'loose' insofar as the switch will not roll back to active and stay locked but there are no GFIs internal to test the circuit and the new fixture is now back off the wall.

The instructions mention 'grounded black' as a possible wiring issue but the wire coming out of the house hasn't been peeled, only the fixture.

Running out of ideas (not even holding the breaker in will restore power).

Do I need a circuit tester to test the outside wires?


Thank You- CharHac



__________________
ch1466 is offline  
 
Reply With Quote Quick reply to this message
Old 06-01-2007, 11:27 AM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,992
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Welcome CharHac:
It sounds like the issue is with the breaker itself rather than with the wiring.
loosen the screw holding the black wire to the breaker, move the wire out of the way, grasp the breaker by the end next to the center of the box and pull it while swinging it away from the center. It will then slip off the pivot easily.
Take the old breaker to Home Depot, Lowes or your local hardware store for a replacement. Attach the wire to the new breaker before installing it, place the heel on the pivot point and click it into place. Now you can turn it on and it should work. OR wait and let the electrician take care of it when he adds the new panel and wiring.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 06-01-2007, 06:56 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

If your panel happens to be a Federal Pacific..
This is a typical problem. The plug in breakers are prone to burning off at the contact point and the breaker gets loose.
The best fix is to replace the panel, but second best is to get a new breaker and find another slot to install it in.

__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Lighting Information Articles DoA General Home Improvement Discussion 1 06-08-2011 05:21 AM
Recessed lighting question RyanBruner Electrical and Wiring 6 11-19-2008 06:21 PM
Lighting Tips William Richardson General Home Improvement Discussion 0 10-24-2007 04:04 AM
Outdoor lighting plan wheelman Electrical and Wiring 3 09-11-2006 05:24 AM
Lighting Tips & Advice - Interesting Reading DoA Electrical and Wiring 0 05-31-2006 04:41 AM