VIEW MY

billhead1

Member

Gift Premium Subscription To billhead1

Join Date:

04-09-2012

Last Activity:

06-04-2014 1:37 PM

Likes Given: 4

1 Likes on 1 Posts 

LATEST ACTIVITY

  • Posted in thread: Best Brushes for Cutting In on 10-15-2012 at 04:17 PM
    Say goodbye to tape.This is not an advertisement, but an endorsement for the best brushes I've
    ever used for cutting in. No tape is needed because the leading edge is like a blade (no
    feathering), but...

  • Posted in thread: Latex paint addative on 08-14-2012 at 08:32 PM
    I like XIM's latex extender much better than Flood's Floetrol. I talked with the local Benjamin
    Moore manager at one location, who has many years of experience and her husband is a paint
    contractor. S...

  • Posted in thread: Oatey's Great White Joint Compound or Harvey's Wet Set PVC Cement for Wet PVC on 08-12-2012 at 08:20 PM
    I replaced my plugged AC condensate P-trap with a P-trap that has an internally threaded
    cleanout plug at the bottom of the trap. Unfortunately, this P-trap has a very small drip in
    the vicinity of th...

  • Posted in thread: Backbrushing A Metal Door on 08-08-2012 at 02:14 AM
    I plan to use a 4" foam roller and back brush my steel back door for coating uniformity. The
    door has a small amount of rust at the bottom, which I was planning to sand with 150 grit
    paper, prime with...

  • Posted in thread: Maximum Allowable Pressure for Washing Bricks & Mortar Joints on 07-30-2012 at 09:21 PM
    What is the maximum recommended pressure for pressure washing to avoid damaging bricks and
    mortar joints?

  • Posted in thread: Foundation Lock Causing Window Lock Problems on 07-15-2012 at 09:26 PM
    Due to foundation problems, the window in the attached photo appears crooked where the upper
    and lower panes meet and will no longer lock on the right hand side (looking out). What is the
    recommended ...

  • Posted in thread: Brick Mortar Repair for Fountain on 07-15-2012 at 08:50 PM
    What is the recommended method for repairing mortar on bricks in the vicinity of a fountain
    (photo attached)?

  • Posted in thread: Soldier Brick Mortar Repair Recommedation on 07-15-2012 at 08:46 PM
    what's the best way to repair the mortar joint between these soldier bricks? Can I use a
    carbide bit on an oscillating tool to clean it out (see photo)?

  • Posted in thread: Aesthetic Repairs to Concrete Curb on 07-15-2012 at 08:42 PM
    Can anyone recommend an aesthetic repair to the concrete foundation curb shown in the photo,
    such as smoothed mortar?

  • Posted in thread: Carport Crack Next to Foundation Curb on 07-15-2012 at 08:38 PM
    I filled this crack with Great Stuff foam to prevent rainwater erosion under the slab (photo
    attached). Is there a toolable concrete material that can be used as a topcoat to blend this in
    with the co...

1 COMMENTS
Posted: 
April 9, 2012  •  09:26 PM
For kitchen odors, if it smells like smoke or grease, talk with a paint supplier about a stain blocking primer. They typically seal the substrate odors well enough to eliminate the smell. Then apply a topcoat of your choice.
Check your curtains and determine if they need laundering.
Clean your drains with bleach followed by a hot water rinse if you suspect a food waste odor, then add some baking soda followed by a cup of vinegar, then rinse with water.
Remove the P trap under the sink and visually inspect it for partial blockage.
Also, deodorize the garbage disposal, as above, if you have one.
 
POST A COMMENT