VIEW MY

gottodo1

Established Member

Gift Premium Subscription To gottodo1

Join Date:

04-15-2013

Last Activity:

11-19-2016 1:43 PM

Likes Given: 6

25 Likes on 23 Posts 

LATEST ACTIVITY

  • Posted in thread: Replacing drip edge problem? on 11-16-2016 at 11:24 PM
    Nope, I was already done by the time you posted :). Thanks for the help oldog, hopefully that
    paper to bridge it will be successful. I had to use a heat gun as it wasn't very pliable at 50F
    even thoug...

  • Posted in thread: Replacing drip edge problem? on 11-12-2016 at 07:21 AM
    Thanks for the reply, I'm going to try to crank this out today. So I'll buy this stuff and use
    about 4 inches to bridge the gap? Is this the stuff you're talking about? or this?
    https://www.menards....

  • Posted in thread: Replacing drip edge problem? on 11-11-2016 at 04:40 PM
    Hi guys, I thought I would be wrapped up today but instead I'm just frustrated. SO I went to
    put on the drip edge today and... I'm still not done after 3 hours. Backstory, when I ripped
    off the old dr...

  • Posted in thread: Roof Water flow issue on 11-09-2016 at 09:18 AM
    I actually hadn't thought about continuing the roof over. I don't hate the gutter idea but
    it'll sure look dumb. I'll think about it this winter and figure out which I want to do. Thanks
    for the thoug...

  • Posted in thread: Roof Water flow issue on 11-08-2016 at 02:44 PM
    Hey Guys, A few weeks ago we had a real rain storm and I identified what I thought was a slight
    roof water flow issue in the roof transition from the house to the garage. That's the photo
    labeled Wate...

  • Posted in thread: Siding Mistake advice on 09-27-2016 at 09:25 PM
    I'm 2 corner pieces short, Once I get those I will post some pictures. The top isn't turning
    out perfectly but I think it will be good enough for a first siding project.

  • Posted in thread: Siding Mistake advice on 09-13-2016 at 05:33 PM
    3/8" below what I would call an acceptable gap.

  • Posted in thread: Siding Mistake advice on 09-13-2016 at 05:32 PM
    HA had another thought. I have some PVC brickmod I cut. I'll just trim the scrap down to that
    size and put it in there so it's even with the brick and it will look decorative.

  • Posted in thread: Siding Mistake advice on 09-13-2016 at 05:01 PM
    Hey Guys, I started putting up this neat brick panels last week and everything was going really
    swell made all the measurements. I went to put up the last layer this week and I see that it
    doesn't mat...

  • Posted in thread: Quiet noisy breakers on 08-03-2016 at 07:15 PM
    Hey Guys, SO my first set of breakers from when I installed my Tankless electric water heater
    started buzzing (quiet but there, not a chatter) when the unit is heating. I hoped changing
    them out may f...

FORUM SIGNATURE
10/11: Bought the perfect house, 11/12: 10k & 200 hours,08/13: 30k & 400 hours into the perfect house, 12/13: 35k & 500 hours,02/14: 37k & 550 hours, 08/14: 38k & 650 hours 05/15: 40k & 700 hours and I think it's done, Home appraised 40k!!! 1 to 1 ratio achieved! 03/16: Filed small claims court on contractor for siding all of previous
1 COMMENTS
Posted: 
August 23, 2013  •  04:26 PM
what a dork
POST A COMMENT


Newest Threads