VIEW MY

Paul678

Gift Premium Subscription To Paul678

Join Date:

11-24-2013

Last Activity:

03-04-2014 1:05 PM

1 Likes on 1 Posts 

LATEST ACTIVITY

  • Posted in thread: Toilet Flapper Closes Too Early on 03-02-2014 at 07:51 AM
    Yes, you can get everything you need at any of the hardware stores.Ok, but should I just
    replace the Mansfield flapper unit?The floater/valve device seems to be working just fine.....

  • Posted in thread: Toilet Flapper Closes Too Early on 03-01-2014 at 05:28 PM
    Not really a whole lot of adjustment possible on this type of setup.The float adjust with the
    metal clip on the metal wire attached the fill valve.If it were me, I'd rip it all out and
    replace everyth...

  • Posted in thread: Toilet Flapper Closes Too Early on 03-01-2014 at 04:32 PM
    Adjust a little more slack in the chain that goes to the flapper and see what happens.Mine
    doesn't have a chain. It's just a metal rod screwed into the handle.But there are holes at the
    end of the rod...

  • Posted in thread: Toilet Flapper Closes Too Early on 03-01-2014 at 03:49 PM
    My toilet doesn't flush solid waste properly. I've already cleared out the outlet holes under
    the rim of the toilet with a coat-hanger wire, but still the flush would back up if I used too
    much toilet...

  • Posted in thread: Security Door Dead Bolt is Misaligned with Hole on 03-01-2014 at 02:49 AM
    It looks like the problem is your door is bent/bowed. The deadbolt bows inward. Looks like
    someone pushed against the door really hard.Hello again, Kok328.Maybe what you are seeing is
    the distortion f...

  • Posted in thread: Security Door Dead Bolt is Misaligned with Hole on 02-28-2014 at 06:49 PM
    You can see here: dead bolt is too low and a bit too forward for the receiving hole. The
    bottom bolt's hole is too low as well, but it still makes it.Here are the holes: the bolts:
    Although the bo...

  • Posted in thread: How to Maintain my 1999 Trane XL1200? (Tucson, AZ) on 02-21-2014 at 09:53 AM
    Yea, the looks of that nipple doesn't look like it wants to be messed with.1) Your solution
    will work just fine with the new coupler.2) Well for one, it will leak from the unit, rust out
    the drip pan,...

  • Posted in thread: How to Maintain my 1999 Trane XL1200? (Tucson, AZ) on 02-20-2014 at 07:08 PM
    Ok, so after using a piece of wire to verify that my p-trap was indeed blocked off, I cut the
    PVC, and.....I couldn't unscrew the first nipple from the pan.It really seemed like the
    installer used glu...

  • Posted in thread: How to Maintain my 1999 Trane XL1200? (Tucson, AZ) on 02-18-2014 at 02:42 PM
    1) Yes2) I don't know anything about S & O but, on a properly install valve, the handle
    perpendicular to the gas line is in the off position.3) Nope, once glued that's it, no
    removing. Nope, you don't...

  • Posted in thread: How to Maintain my 1999 Trane XL1200? (Tucson, AZ) on 02-18-2014 at 02:04 PM
    1) yes, this is fine2) yes, make sure there is no physical matter in the p-trap.open the unit
    and find the drip pan. make sure the drip pan is clean. if you can remove the p-trap and blow
    air through ...

0 COMMENTS
POST A COMMENT