DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > Replace bottom garage door panel




Help Support House Repair Talk by donating using the link above.
Reply
 
Thread Tools Search this Thread
Old 07-25-2017, 12:49 PM  
kdrymer
Member
Join Date: Aug 2014
Posts: 84
Liked 4 Times on 4 Posts
Likes Given: 2

Default Replace bottom garage door panel

Hello - The bottom panel of my overhead garage door has rusted and caused corrosion to the point where it really needs replacing. The door is supported by an extension spring lift system (no garage door opener). I don't have a set of come along's to tension the cable while I remove the lift cable away that's attached to the bottom of the bottom panel. As an alternative I was thinking of doing the following (tell me if you see any issues):

1. Raise the door entirely to relieve spring tension
2. Prevent the door from moving with a pair of vice grips attached over the tracks on the 2nd panel (above the bottom)
3. With the tension off the springs, remove the lift cable from each end of the bottom panel
4. Remove the hinges fastening the bottom panel to the 2nd panel above
5. Support the bottom panel and carefully lower it down to rest on the ground
6. Remove bottom panel from tracks and install new panel
7. Repeat Steps 1-5 in Reverse sequence

P.S. This is an older door (Raynor "Decade" model) so if I can not locate an OEM replacement I may need to replace the entire door, but wanted to see if this replacement method would work if I can find a new individual panel.


kdrymer is offline  
 
Reply With Quote
Old 07-25-2017, 01:00 PM  
nealtw
Contractor retired
 
nealtw's Avatar
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 23,035
Liked 2826 Times on 2481 Posts
Likes Given: 4660

Default

We have a garage door company here, when I go by their shop it looks like they save every old good panel that they remove when replacing doors. I would look around , used building material store and Craigslist adds.

Chain and turnbuckle might be usable for the spring. Something heavy enough for the load.
http://www.homedepot.com/p/National-...TBKL/204660098


nealtw is offline  
 
Reply With Quote
Old 07-25-2017, 03:20 PM  
kok328
Senior Member
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,716
Liked 240 Times on 203 Posts
Likes Given: 111

Default

There will still be some spring tension with the door full open.
Don't attempt any short cuts. Unload the spring by hand and then you can proceed however you want.
Besides you'll want to make sure both sides are equal and rebalance the door after panel replacement.
kok328 is offline  
 
Reply With Quote
Old 07-25-2017, 05:30 PM  
Snoonyb
Senior Member
Join Date: Sep 2006
Posts: 2,155
Liked 381 Times on 337 Posts
Likes Given: 1

Default

When the door was installed the springs were loaded after the assembly was complete. Reversing the process will insure your safety.
__________________
Illigitimas non-carborundum
Snoonyb is offline  
 
Reply With Quote
Old 08-18-2017, 10:20 PM  
JohnMcNally
Junior Member
Join Date: Oct 2016
Posts: 7
Liked 2 Times on 2 Posts
Likes Given: 1

Default

I don't think that there is any kind of issue in this.


JohnMcNally is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Garage door bottom weather seal p3arljam General Home Improvement Discussion 9 09-08-2015 10:49 PM
water come in from bottom of patio door qmqmqm Decks & Patios 5 09-14-2013 06:16 AM
sealing bottom of door in garage? qmqmqm Insulation and Radiant Barriers 3 04-08-2013 06:15 PM
Casement Window - Bottom of Frame Rotted - Repair or Replace? soulman1980 Windows and Doors 4 06-07-2012 08:05 AM
replace garage door opener cfli1688c1 Windows and Doors 1 01-14-2010 01:22 PM



Newest Threads