DIY Home Improvement, Remodeling & Repair Forum > Appliances > HVAC > Wiring an "override" thermostat


Reply
 
Thread Tools Search this Thread Display Modes
Old 12-05-2016, 06:22 PM  
nealtw
Contractor retired
HRT_SUPPORTER.png
 
nealtw's Avatar
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 21,554
Liked 2453 Times on 2160 Posts
Likes Given: 4137

Default

Quote:
Originally Posted by Chris View Post
I had to jump a wire to the fan switch in the furnace so it would come on with the heat. I guess I could put a manual switch for fan only but I don't think I have ever run just the fan by itself before.
Before anyone had AC that was common here to pull cooler air from the basement.


nealtw is offline  
 
Reply With Quote
Old 12-05-2016, 06:34 PM  
kok328
Established Member
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,662
Liked 225 Times on 191 Posts
Likes Given: 102

Default

Quote:
Originally Posted by Chris View Post
I had to jump a wire to the fan switch in the furnace so it would come on with the heat. I guess I could put a manual switch for fan only but I don't think I have ever run just the fan by itself before.
Didn't realize you jumper the fan to the heat, I thought you just stole the fan wire and left G open.
Won't your fan come on via control board relays in heat mode?

You'll be blowing cold air while the system is proofing the safetys (~1min), coming up to temp.
If your fan runs after burner shuts down then the control board is running the fan.
This is good to cool down the heat exchanger and get the most out of the warm ducts.



Last edited by kok328; 12-05-2016 at 06:37 PM.
kok328 is offline  
 
Reply With Quote
Old 12-05-2016, 06:35 PM  
Chris
Guru of nothing
HRT_ADMIN.png
 
Chris's Avatar
Join Date: Jul 2013
Location: , Southern California
Posts: 4,087
Liked 828 Times on 624 Posts
Likes Given: 97

Default

Makes sense I never had a basement before and we just used regular fans because I grew up with wall heaters
Chris is offline  
nealtw Likes This 
Reply With Quote
Old 12-10-2016, 10:04 PM  
slownsteady
Administrator
HRT_ADMIN.png
 
slownsteady's Avatar
Join Date: Jun 2009
Location: Newton, NJ
Posts: 5,747
Liked 959 Times on 796 Posts
Likes Given: 1609

Default

Getting off topic here. The OP never mentioned anything about fan switches. It sounds like he wants a master t-stat to control two downstream t-stats for override ability.
__________________
Learn something every day
---
SnS
slownsteady is offline  
 
Reply With Quote
Old 12-11-2016, 10:35 AM  
buffalo
Established Member
Join Date: Nov 2013
Posts: 267
Liked 47 Times on 40 Posts
Likes Given: 120

Default

Or set a program on a program able tstat, when you bump the temp up or down , it will go back to the program at the next programmed temp change.

And cris , how long of a tstat wire run is it . Somtimes nobody stapled it in the wall and you can tie a new wire to it and pull it through. Or if the existing wire drop straight to the basement you can use a long tiny chain , shove it in the hole in the drywall , jigel it around and it falls through the hole in the floor , tie a new wire to it .
buffalo is offline  
 
Reply With Quote
Old 12-11-2016, 06:13 PM  
Chris
Guru of nothing
HRT_ADMIN.png
 
Chris's Avatar
Join Date: Jul 2013
Location: , Southern California
Posts: 4,087
Liked 828 Times on 624 Posts
Likes Given: 97

Default

It goes down then over about 20 feet then down again. I might try and pull a new wore but I will wait until I am living in the house and it is summer so I have time.


Chris is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
"Fan on" option on thermostat not working Emac HVAC 9 10-14-2015 05:31 AM
Difference between "baseboards" and "moulding" panzerfaust0 Walls and Ceilings 8 01-18-2012 02:55 AM
wiring "issues" jdenn4 Electrical and Wiring 3 11-22-2010 08:42 AM
Furnace not shutting off when thermostat switched to "heat" rasilun HVAC 1 01-06-2010 03:12 PM
Totaline thermostat blinking "Heat On" before the fan comes on. Maybeitwillwork HVAC 1 01-24-2009 10:20 PM





Newest Threads