DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > Adjusting New Bathroom Door




Help Support House Repair Talk by donating using the link above.
Reply
 
Thread Tools Search this Thread
Old 10-12-2017, 11:09 AM  
Bones032
Junior Member
Join Date: May 2017
Posts: 5
Default Adjusting New Bathroom Door

I own a home that is 98 years old, which means things are not perfectly made. I am trying to put a new door in the bathroom. I noticed the door frame is off a bit, causing the new door not to fit properly. The door frame is a quarter inch higher on the handle side than on the hinge side.

When the door closes, the bottom half of the door, up to about the handle is perfectly flush to the frame. But, from the handle up, the door starts to slant away from the frame, allowing a gap. Also the top of the door has a slanting gap as well, from the hinge side being pretty good, to a big gap on the handle side.

Since I know the frame is off, causing these issues, what can I do to adjust the door. I tried adding a skinny shim underneath the bottom hinge, hoping that would push the top right of the door over more, but it did not really help. Should I try cutting a door an angle to match the frame being off?

Any Ideas are appreciated. Pics below. The 1st pic shows how the door is flush to the frame at the bottom. 2nd pic you can see the gap starting, and then the 3rd pic the full gap to the top of the door. 4th pic if the gap on the top of the door.


Click image for larger version

Name:	20171011_175340.jpg
Views:	24
Size:	44.5 KB
ID:	14873   Click image for larger version

Name:	20171011_175406.jpg
Views:	25
Size:	46.0 KB
ID:	14874   Click image for larger version

Name:	20171011_175413.jpg
Views:	26
Size:	35.6 KB
ID:	14875   Click image for larger version

Name:	20171011_175105.jpg
Views:	24
Size:	36.4 KB
ID:	14876  
Bones032 is offline  
 
Reply With Quote
Old 10-12-2017, 01:40 PM  
RobertThoreson
Junior Member
Join Date: Oct 2017
Location: Marinette, Wisconsin
Posts: 9
Liked 2 Times on 1 Posts

Default

I would think about making the frame square again. It's not as hard as you might think. Pull the trim off and shim it where it needs it


RobertThoreson is offline  
 
Reply With Quote
Old 10-12-2017, 02:40 PM  
Snoonyb
Senior Member
Join Date: Sep 2006
Posts: 2,287
Liked 402 Times on 357 Posts
Likes Given: 1

Default

Your alternatives range from a lot of work to relatively easy.

The really difficult involves jacking the house up to level.

The relatively easy is to cut the top of the door, raise the hinges on the jamb or lower them on the door, adjust the lock strike plate and adjusting the door stop on the latch side.
__________________
Illigitimas non-carborundum
Snoonyb is offline  
 
Reply With Quote
Old 10-16-2017, 08:18 AM  
slownsteady
Administrator
HRT_ADMIN.png
 
slownsteady's Avatar
Join Date: Jun 2009
Location: Newton, NJ
Posts: 6,306
Liked 1112 Times on 921 Posts
Likes Given: 1830

Default

Have you held a level against the vertical sides of the door frame?
__________________
Learn something every day
---
SnS
slownsteady is offline  
 
Reply With Quote
Old 10-16-2017, 09:31 AM  
mabloodhound
Restoration & Renovations
Join Date: Jun 2008
Location: Halifax, MA
Posts: 90
Liked 20 Times on 15 Posts
Likes Given: 18

Default twisted

You've got a couple things going on. First, either the frame is twisted or the door itself is not flat. This causes the gap at the stop trim at the top. You can set that top hinge in further (not deeper) and/or move that trim stop to allow the door to fully close. Or a combination of both of those; move hinge in a bit and move stop a bit (which is what I do to make it less conspicuous). But make sure it isn't a warped door first.
Now for he gap at the top header. I would probably just cut a wedge to glue to the top of the door to fill that gap. Make it slightly wider that the thickness of the door and sand it flush after installation. Paint it all and it will blend in.

Dave Mason


mabloodhound is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Adjusting Valves in Washing Machine Outlet Box jniter Plumbing Forum 4 07-16-2011 10:55 PM
Painting The Bathroom Door Kithikor General Home Improvement Discussion 1 04-27-2011 06:23 AM
adjusting water in an old case 50 toilet dodgers Plumbing Forum 4 03-15-2009 09:43 PM
Stuck Bathroom Door thenewguy Carpentry and Woodworking 3 03-05-2008 10:23 AM
kenmore icemaker speed needs adjusting rpmooney Introductions 1 07-20-2006 11:45 AM