DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > New Shower




Reply
 
Thread Tools Search this Thread Display Modes
Old 09-16-2005, 10:09 AM  
cami7
Junior Member
 
Join Date: Sep 2005
Posts: 8
Default New Shower

it is expensive to replace your shower/tub?
I hate the tub/shower and want the tub out to jsut have a nice stand up shower but not sure if it is expensive to do that



__________________
cami7 is offline  
 
Reply With Quote Quick reply to this message
Old 09-16-2005, 10:32 AM  
Cam60
Junior Member
 
Join Date: Sep 2005
Posts: 2
Default

it depends i would imagine if they can get the tub out the door or if they have to take out the window to get it out then repair the window afterwards
anyone else around who can help?



__________________
Cam60 is offline  
 
Reply With Quote Quick reply to this message
Old 09-16-2005, 02:07 PM  
candyman
Junior Member
 
Join Date: Sep 2005
Posts: 3
Default

they had to get ours out from the window and what a mess the entire window was taken out then some but it was well worth it in the end

__________________
candyman is offline  
 
Reply With Quote Quick reply to this message
Old 09-17-2005, 10:25 PM  
Daryl
Member
 
Join Date: Sep 2005
Posts: 80
Default tub replacement

What type of tub are you removing? If it's cast iron you can remove it by breaking it apart with a sledge hammer and removing it in pieces small enough to handle. If it's steel it shouldn't be too heavy to carry out the door.

__________________
Daryl is offline  
 
Reply With Quote Quick reply to this message
Old 09-19-2005, 10:37 AM  
cami7
Junior Member
 
Join Date: Sep 2005
Posts: 8
Default

it is a regular tub nothing fancy white it came with the house but I think it maybe to big to get through the door and down the hall

__________________
cami7 is offline  
 
Reply With Quote Quick reply to this message
Old 09-19-2005, 03:36 PM  
Daryl
Member
 
Join Date: Sep 2005
Posts: 80
Default

Might want to get out your trusty measuring tape and measure your tub. It shouldn't be but five foot long 30-32 inches wide and 15-17 inches deep. Your normal door opening should be 6 1/2 feet high - 30-32" wide. that would give plenty of room for getting a tub through if set on end. Stil the biggest worry is the weight. Is this tub set into an alcove? Do you have three walls surrounding it? One side is finished to the floor - the other sides have a wall coming down to the tub surface.(or is it a claw foot which sits on the floor by itself, oval in shape.) If it's a claw foot, see if a magnet will stick to it and if it's pretty thick . if so it's cast iron and the only easy way to remove it is to break it apart with Mr. Sledge Hammer. Good luck

__________________
Daryl is offline  
 
Reply With Quote Quick reply to this message
Old 09-20-2005, 08:54 AM  
bondo
Junior Member
 
Join Date: Sep 2005
Posts: 13
Send a message via AIM to bondo Send a message via MSN to bondo Send a message via Yahoo to bondo
Default

Most normal tubs will go out a door opening smaller than 30 inches by turning it sideways. Cast iron ones are very strong & heavy, that is why they are good place to go in event of a tornado. Personaly, I would think twice before I removed one if I lived in Tornado alley without a storm shelter. You might be removing the last safe place to go in an emergency.

Removing large cast iron double tubs or whirlpool baths are another matter entirely.

I helped a friend take out a heart shaped cast iron tub once and it nearly kill us going down the stairs.

Good Luck,

__________________
bondo is offline  
 
Reply With Quote Quick reply to this message
Old 09-24-2005, 10:32 AM  
beachy
Junior Member
 
Join Date: Sep 2005
Posts: 5
Default

Glad you did not get killed Bondo!
They had to take ours throught the window we have a 2story house and I guess going down the stairs was not a option lol But I LOVE our new shower,it is a open one and they put in a skylight so it just wakes you up in the morning with the waterfall effect as the water comes out of the wall I guess you could say lol
(Notice I am remodling the entire house lol)
__________________
beachy is offline  
 
Reply With Quote Quick reply to this message
Old 09-25-2005, 02:55 PM  
FirTrader
Member
 
Join Date: Sep 2005
Posts: 51
Default

A clawfoot should be taken out by some local reusables fella - they're worth a bit. A steel tub comes out either by removing the drywall around it, or by cutting the bugger in half with a sawzall with a metal cutting blade in it. This is a two-man procedure - one cuts, and the other sprays WD40 at the blade. See if you can beat 3 minutes 44 seconds! Same goes on the no-doubt totally frozen drain on the tub - cut it with the sawzall and then it'll spin like magic.

Tubs are kind of a drag, but usually getting them in and out of the building is far easier than squeazing a 59 3/4 inch tub into a 60 inch spot diagonally... stupid pythagorean theorem!

If you are going to a stand up shower from a tub, then you have drywall and flooring repairs to do, as well as re plumbing.



__________________
FirTrader is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Tub faucet leak when shower is on? sbattisti Plumbing Forum 31 09-01-2011 09:59 AM
Can you help a newbie renovate the bathroom shower? cyancat General Home Improvement Discussion 16 05-30-2008 07:47 AM
rebuilding shower floor gregrph General Home Improvement Discussion 7 05-29-2008 11:27 PM
Replace Jacuzzi with shower? mustanger General Home Improvement Discussion 5 01-29-2008 06:20 PM
Noise from Shower Valve nikon876 Plumbing Forum 2 02-28-2007 07:11 PM

Newest Threads

LATEST SPONSOR DEALS