DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Powdercoat / Re-Pocelain Cast Iron Kitchen Sink

Thread Tools Search this Thread Display Modes
Old 03-25-2011, 06:21 PM  
Junior Member
Join Date: Mar 2011
Location: Los Angeles, CA
Posts: 1
Default Powdercoat / Re-Pocelain Cast Iron Kitchen Sink

Hello all, I would like to re-porcelain my kitchen sink. Double basin with integral backsplash for wall mount faucet. Porcelain is worn at the drain holes, pitting around the bottom of bowls and worn center divider rail. Otherwise it is perfect. Problem is I cannot find anyone who can do this (Southern Calif.) The question may have been posed before but any merits to powdercoating a cast iron kitchen sink? I've read its a similar process as porcelain but the firing temp is around 400-500 degrees rather than 1350-1400 degrees. Result is surface is not as hard as porcelain but better than epoxy reglazing. Just wondering, are there other applications / methods that use a high firing finish?

Btw, the sink is not installed and can be transported. Any comments / suggestions appreciated.

bange is offline  
Reply With Quote
Old 03-26-2011, 01:23 AM  
Certified Lunatic
Redwood's Avatar
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887

Why not just get a new sink?

Are you emotionally attached to this one?

Redwood is offline  
Reply With Quote
Old 03-26-2011, 11:33 AM  
Senior Member
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,499
Liked 82 Times on 67 Posts
Likes Given: 2


Powder coating is done over a metal surface not a hard porcilin surface.
A new sink would be the longest lasting idea.
joecaption is offline  
Reply With Quote
Old 04-01-2011, 04:16 PM  
Junior Member
Join Date: Apr 2011
Location: Pinehurst, North Carolina
Posts: 3

You can powder coat anything that will take 400* for 20 minutes (plus the time it takes for the part itself to get to 400* and cool off afterwards).

If you can't get a charge through it for the powder to stick you can heat the item up and shoot it hot so the powder melts and sticks when it hits. We did this on probably 30 plastic intake manifolds for cars, and the plastic ignition coils.
BDSmith is offline  
Reply With Quote
Old 04-01-2011, 05:05 PM  
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,167
Liked 1303 Times on 1146 Posts
Likes Given: 2200


BD: Do you think it would stand up to the ware and tare of a sink?
nealtw is online now  
Reply With Quote
Old 04-01-2011, 10:09 PM  
Junior Member
Join Date: Apr 2011
Location: Pinehurst, North Carolina
Posts: 3

There are a few different powders. You can get a commercial powder that is made for high impact resistance and you'd be close to 100% okay. I'll be honest that nothing is like that ceramic coating that comes on appliances, sinks, etc.

IF it is cured correctly and IF the correct powder is used I'd feel confident in it. We did mostly custom car parts with all sorts of ridiculous colors so wear, impact resistance, and UV resistance was never an issue if the color was right. Because of that we never got into all the specifics with the commercial quality stuff but I know it's out there. Condos and apartments use it on their railings for example, but that's a UV resistant application that you don't need for a sink.

You can have them put a coat or two of clear powder on there also that would help. Car guys are a lot more anal about scratches but you can wet sand and buff that stuff out.

Go to someone that has a clue what's going on. There are a couple powder forums (ColumbiaCoatings has a good one) and you can find someone local that isn't just going to throw it in with another batch and guess that it is GTG. Plus you probably won't get charged and arm and a leg as the big commercial guys HATE cleaning their guns out to switch colors/powder for your one application.

I'm guessing you'd want it white. Cleaning the guns becomes 10x an issue because EVERYTHING shows up in white, so if you shot a darker color (pretty much any) you may or may not see it. We'd get guys that were holding parts in their hands and go "Oh man, what is that?" Put it 3 feet away under your hood and it's fine. Stuff they'd NEVER see if they weren't inspecting it before they installed it.

Hopefully that makes sense, I've had a couple too many beers tonight
BDSmith is offline  
Reply With Quote
Old 04-01-2011, 10:12 PM  
Junior Member
Join Date: Apr 2011
Location: Pinehurst, North Carolina
Posts: 3

Here's a chart that should get you close. If the powder coater doesn't have a clue about the different powders I'd avoid them. Like I said, we never cared about all the factors as long as the color was right, but at least we knew there were other factors if the situation dictated it.

BDSmith is offline  
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Can't get the drain out of an old cast iron tub runner041 Plumbing Forum 6 01-26-2011 01:01 AM
Grab bar for cast iron tub Laren Plumbing Forum 4 08-28-2010 04:57 PM
Setting cast iron tub in place? StevenC Plumbing Forum 5 06-19-2010 06:03 PM
new cast iron sink with formica counter vintage_car Plumbing Forum 8 01-15-2010 07:47 AM
Old Cast Iron Drain Leaking jameslward Plumbing Forum 10 02-02-2009 09:23 PM

Newest Threads