DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Painting Forum > Advice needed on painting door frames/doorsand




Reply
 
Thread Tools Search this Thread Display Modes
Old 08-17-2011, 07:23 PM  
barnettca
Junior Member
 
Join Date: Aug 2011
Location: kitchener, ontario
Posts: 2
Default Advice needed on painting door frames/doorsand

We are in our first house and learning all about painting "rules". So....the doors and frames in the hallway are painted a soft cream colour. Inside my son's room, he wants the walls a bright blue and the frames/door all done in a silver/grey. I am just not sure what part of the door frame I should be painting this colour? The door opens into his room. Do I do the sides of the door in the silver-grey as well as the part in his room. Where do I end with the silver grey on the frame/jam? Thanks for ANY and ALL assistance.



__________________
barnettca is offline  
 
Reply With Quote Quick reply to this message
Old 08-17-2011, 09:10 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,748
Liked 926 Times on 826 Posts
Likes Given: 1595

Default

When standing in the hall with the door closed everything should be cream and when standing in the room with the door closed silver. There are two places in there where you can stop, it,s your choice whichever you find easier.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 08-18-2011, 07:51 AM  
barnettca
Junior Member
 
Join Date: Aug 2011
Location: kitchener, ontario
Posts: 2
Default

Thank you Neal. Guess I was over-worrying and didn't think to just close the door and do that!

__________________
barnettca is offline  
 
Reply With Quote Quick reply to this message
Old 11-18-2011, 12:29 AM  
cmj
Junior Member
 
Join Date: Nov 2011
Posts: 1
Default What if there is no door?

I have a similar problem - but its a hallway - living room transition. We want to stain the hall door jamb and trim, but can't do it in the Living Room. Where do I draw the line between stain and paint?

__________________
cmj is offline  
 
Reply With Quote Quick reply to this message
Old 11-18-2011, 12:47 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,748
Liked 926 Times on 826 Posts
Likes Given: 1595

Default

Just close the door, everything you see from that side should match. No door? flip a coin.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 11-18-2011, 07:15 AM  
joecaption
Senior Member
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,368
Liked 38 Times on 33 Posts
Likes Given: 2

Default

When it comes to an open or arch way I suggest figuring out which side is going to be viewed the most, but as suggest it's a matter of what looks good to you.
Anytime your going to any dark color from a light one, to prime the walls first with primer that's been tinted a dark gray, and never buy cheap paint. If you skip one of these tips, plan on having to paint at least 3 to 7 coats to get the wall looking so the color evens out.
Time after time I've suggest this to customers and they skipped the priming with gray step to save money or time then try to paint a dark blue or burgendy color over white then end up spending more money on paint and two or three days painting this one wall.
Clean, then sand the whole wall with a sanding pad on a sanding pole, that will find all the flaws in the wall and old paint runs before you paint so they can be fixed before painting.
If you have not done much painting before, do not use blue tape, it's expencive, you will end up getting paint under the tape or peeling the new paint off the wall. Buy quality roller covers and a Purdy 1-1/2 sash brush and learn how to use it, it will save you a lot of time. Cheap roller fall apart and leave lint, a cheap brush will leave paint lines and the brushes fall out.
You only need to use the first third of the brisles. Do not wipe the brush on the side of the can, just tap the brush on the side and twist it as you move toward the wall to stop it from dripping, Do not have a full brush when trying to cut in, wipe some on the wall about an 1" away then work you way to the trim.
Paint the ceiling first, paint all the trim next, then do all your cut in around the trim and inside corners before trying to roll the walls.
More info then you asked for, but so be it.



__________________
joecaption is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Capacitor advice needed gbharrington General Appliance Discussion 2 09-25-2010 10:33 AM
Basement Window Advice needed MikeyL Windows and Doors 1 05-27-2009 06:50 PM
Furnace Advice Needed gunit HVAC 3 01-10-2009 04:17 PM
Steel & aluminum window/door frames get very frosty Quattro Windows and Doors 2 02-13-2008 03:03 PM

Newest Threads

LATEST SPONSOR DEALS