DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > Should this header be supported by double studs?




Reply
 
Thread Tools Search this Thread Display Modes
Old 11-16-2011, 11:13 AM  
revg
Junior Member
registry_dropdown_24643_63828
 
Join Date: Nov 2011
Posts: 1
Default Should this header be supported by double studs?

Hi Guys,

I decided to get a window in my living room extended and installed. When the install crew left a bunch of my electrical wasn't working so it prompted me to get a master electrician in to open up the job and check it. He told me the job was very poorly done and nothing was up to code, it was totally unsafe, and the people doing it clearly had no knowledge of the Canadian electrical code.

He then told me that the header they installed is only supported by single studs and he said it looks like it should be supported by double studs. He wasn't sure, but wanted me to ask a framer just to make sure that this header installation was up to code. Here are the pictures. Can anyone tell me if this header should be supported by double studs or not?

image1
image2
image3

Thanks,
Greg


revg is offline  
 
Reply With Quote
Old 11-16-2011, 12:46 PM  
joecaption
Senior Member
registry_dropdown_21184_63834
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,501
Liked 83 Times on 68 Posts
Likes Given: 2

Default

There called jacks, not studs, studs go from bottom plate to top plate. Code or not I still would have used two. They knew the sheetrock was going to have to be repaired anyway and it's easer to fix a wide piece of rock then to patch a small strip of it.
Do you replace that window with one that was just taller or is this a whole new window?
Why is that wire sticking out of the header?
They may have only used one if it's one the gable end side of the house because there's far less weight above it then a front or back wall.



Last edited by joecaption; 11-16-2011 at 02:24 PM.
joecaption is offline  
 
Reply With Quote
Old 11-16-2011, 05:41 PM  
nealtw
Contractor
registry_dropdown_20526_63847
 
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,179
Liked 1306 Times on 1149 Posts
Likes Given: 2208

Default

Out here we call them criples or criple studs. Any header 5 ft or longer should have at least two on each end. As Joe said, It depends on whats above it. If there is a floor or rafters or trusses that land on this wall, it will be a concern. There should be 3 nails or screws every 16" and there should be no holes near the bottom or top of a header.
Let us know what's above.
nealtw is offline  
 
Reply With Quote
Old 11-16-2011, 06:25 PM  
joecaption
Senior Member
registry_dropdown_21184_63850
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,501
Liked 83 Times on 68 Posts
Likes Given: 2

Default

A cripple stud is the short ones above and below a window opening, not the one holding up the header. And the full length one to the left and right of the jacks is called a king stud.
Just so were all on the same page, here's a page.
On The House with the Carey Bros. & Rebecca Cole. : The Anatomy Of A Door Opening -> Weekly Project

Last edited by joecaption; 11-16-2011 at 06:48 PM.
joecaption is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Studs - wooden or steel johnnymnemonic General Home Improvement Discussion 8 11-09-2011 08:58 PM
r20 insulation with 2x4 studs in Garage cmarlo Framing and Foundation 2 04-08-2011 06:29 AM
Question regarding an existing beam being supported with a post... Shortmag Framing and Foundation 11 01-01-2011 10:56 AM
Metal studs mmcvicker Electrical and Wiring 3 01-10-2008 10:43 AM
Drywalling: No studs in Corners milbry18 Walls and Ceilings 1 08-20-2007 06:58 PM

Newest Threads

LATEST SPONSOR DEALS