DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > Walls & ceiling problems & advices




Reply
 
Thread Tools Search this Thread Display Modes
Old 08-06-2012, 06:52 AM  
condoowner
Senior Member
registry_dropdown_17185_75819
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

Its bin... I haven't had this problem anywhere except on these 3little spots...

I suspect I either forgot to prime some putty touch ups before painting or a last minute sanding to remove some clumps in the prime caused this ..

Either ways I am learning from my mistakes...

Could I locally apply more paint with a 4" roller and sand smooth before the 2nd final coat goes on??

Should i just prime on top and repaint??

I will post pics whenever my camera battery is charged.



Last edited by condoowner; 08-06-2012 at 06:57 AM.
condoowner is offline  
 
Reply With Quote
Old 08-06-2012, 04:01 PM  
condoowner
Senior Member
registry_dropdown_17185_75833
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

Ok back to the ceiling fan issue, I went to the attic and took some pics as promised.. THere are 2x4's running down the ceiling. See pics. Basically I could either climb up the attic and install some bracing myself, or hire a contractor to do it, or use a gizmo that I purchased (and was looking to bring back to the store) to install fans when no bracing is available.

I have a hard time to use the gizmo thing since I cant visually confirm it is engaged properly in the studs, and also its nearly impossible to insert in the electric box hole without struggling and risking the ceiling freshly painted.

I am considering going back in the attic and climb up the ceiling and screw a 2x4 between the studs.. That way, it will be reliable. Only I am scared to go through the ceiling and fall down. I would not survive 25ft... Any chances this happens? In other words, do you think this structure can support my weight (200#) without buckling, breaking or twisting?


IMG_0657.jpg   IMG_0653.jpg   IMG_0651.jpg  
condoowner is offline  
 
Reply With Quote
Old 08-06-2012, 08:17 PM  
nealtw
Contractor
registry_dropdown_20526_75842
 
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 12,851
Liked 1267 Times on 1117 Posts
Likes Given: 2123

Default

The framing will carry the weight, the trick is to nail 2x4 across 2 trusses so you can climb up safely like a ladder. While you are up there you should apply poly behind the box and tape it to the vapour barrier to close the air leak.
http://www.house-improvements.com/va...y-installation
nealtw is offline  
condoowner Likes This 
Reply With Quote
Old 08-26-2012, 08:10 PM  
condoowner
Senior Member
registry_dropdown_17185_76483
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

I just though to give an update while I am asking once again for the expert's opinions!!

The ceiling fan is now installed. I went to the attic and screwed a piece of 2x4 across the ceiling trusses, and used an electric box extension to match the ceiling depth. The fan installation seems sturdy and I think this will be OK.

While I was in the attic, I took some pictures of the structure as we were discussing initially in this thread. I have notiuced some vertical members that were warped and I took a picture of the piece of wood that snapped.

Are these warped pieces normal??? Should we worry?
IMG_0667.jpg   IMG_0655.jpg   IMG_0656.jpg  
condoowner is offline  
 
Reply With Quote
Old 08-26-2012, 08:26 PM  
nealtw
Contractor
registry_dropdown_20526_76484
 
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 12,851
Liked 1267 Times on 1117 Posts
Likes Given: 2123

Default

The broken piece of 1x4 was a temp brace to hold the truss in place before he got on top to place the 2x4s on the flat. When he was on top of the roof and wanted to adjust the truss to fit the line of the flat 2x4s he just reached down and broke the temp brace. The trusses are made with dry lumber so that warped peice was likely there when it was built. Trying to staighten it now will raise the roof or lower the ceiling so I wouldn't touch it or worry about any of this.
nealtw is offline  
condoowner Likes This 
Reply With Quote
Old 08-26-2012, 08:32 PM  
condoowner
Senior Member
registry_dropdown_17185_76485
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

Excellent! Nice to hear that everything is fine! Case closed then! Thanks a lot Nealtw, im learning a lot here!!!


condoowner is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
old lumpy walls and ceiling frogholler Walls and Ceilings 1 11-09-2010 05:10 PM
Ceiling or walls...which first? handy Walls and Ceilings 1 01-06-2010 07:49 PM
new walls and an old ceiling learning Walls and Ceilings 6 10-17-2008 07:18 PM
Asbestos in walls and ceiling? FearfulOfAsbestos Walls and Ceilings 12 12-27-2007 11:01 AM
Wood walls and ceiling Mudball Carpentry and Woodworking 4 06-02-2006 04:55 PM

Newest Threads

LATEST SPONSOR DEALS