DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > Possible mold problems??




Reply
 
Thread Tools Search this Thread Display Modes
Old 05-20-2013, 01:50 PM  
condoowner
Senior Member
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default Possible mold problems??

Hello,

I am currently repainting my bedroom, and I was surprised to see the Zinsser Bin peeling off from the lower corner of the window frame. I applied a second coat but same thing. Grey-ish spots also appeared thru.

I then decided to investigate further and touching the corner it felt humid. I decided to drill a small hole but past the first 32nd of an inch, it was much softer, not quite like mush but softer than the surrounding wood.

Not long after I decided to open the corner (not sure if this was a good idea) and the wood I puled from the hole was wet!

There is water infiltration somewhere but where??

My uncle just went through a nightmare with mold growth in his basement, and as a result, he had half of the house stripped down and rebuilt. He had $70k of damage.

Im extremely concerned and I know nothing about the way windows are built and installed. Can the whole wall be in need of stripping down????

Anynbody with opinions are more than welcome to share... Im very anxious to see what people here think...
Thanks!

EDIT: please note that I tore apart the wood, thats why you see chips and chunks laying around like that.



IMG_0886.jpg   IMG_0887.jpg   IMG_0888.jpg   IMG_0889.jpg  
__________________

Last edited by condoowner; 05-20-2013 at 01:53 PM.
condoowner is offline  
 
Reply With Quote Quick reply to this message
Old 05-20-2013, 10:56 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,754
Liked 928 Times on 828 Posts
Likes Given: 1596

Default

If this is strata titled condo the outside envelope may be a problem for the strata.
Ater that this should be opened up for discouvery, likely you will find poor installation of the window and that takes you back to the strata.



__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 05-21-2013, 08:55 PM  
condoowner
Senior Member
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

Thanks nealtw for replying. You have helped so much on this forum since I registered!

I've spoken to the strata, and we will call a contractor to look at the issue, possibly replacing the window and open up the wall to see if mold/mildew are growing in the wall cavity. For personal interest and education, I would like to get some kind of cross section of a typical exterior wall with a window to see how its assembled and supposed to be..

So lets assume the sill, and window sides (whatever they are called) are in need of replacement, and also the window is in need of replacement, would the drywall and studs also need to be pulled out?

I suspect the best course of action is to wait for the contractor to show up, strip down the sill and window and see whats inside..

On a different (but not unrelated) note, what would window sill bulging means? Most of the sills in my place are slightly bulging up in the center, kinda like if wood was expanding but had no space to do so...

__________________
condoowner is offline  
 
Reply With Quote Quick reply to this message
Old 05-21-2013, 11:15 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,754
Liked 928 Times on 828 Posts
Likes Given: 1596

Default

http://www.mtcc1170.com/images/BCRainScreen.pdf
I think you're in Montreal, if so I beleive the above data applies to you there.
Print it, read it , learn it and teach other people about it untel you are the expert and don't accept a contractor that doesn't know more about it that you do. In an attempt to make building tight here they sealed them up to tight and we ended up with what is known as leaky condo syndrom. Older houses leaked like anything and when water got into the walls it could escape over time. Your building may be older but the newers window were installed in that time or the building was built in that time.
Your windows have an R value of 5 if you are lucky. The insullation they stuffed in the 1/4" beside the window really gives no R value and when moisture gets into it and condences it is wet and stays wet and that the biggest problem.
What you will likely find the vapour bearer stopped at the surface of the wall and should have been wrapped out and behind the house wrap on the outside of the house.
The rainscreen system just accepts the fact that water will get in around the window and needs a way out. The bottom sill ( rough open)is covered with a peel and stick product that has a name but we just call it blue skin that over laps the outside house wrap by 3 or 4 inches , a 2" strip streched into the corner on both side and down the outside at 45 degrees. And a 4" wide strip at the bottom of the sides. House wrapor tar paper is extended on both sides into the cavity and taped to the old house wrap. So any water getting in this area has a path out. Don't do the top, with a chance of a roof leak or some other problem it could bring water into the house with nowhere to go so we leave that one out. The window is installed on plastic horseshows that are 1/4" thick and 1/8 horseshoes are placed behind the nailing flange across the bottom at each nail. The flashing at the top has new instructions as to how to bend the ends to stop wind drivin rain and it wants to be behind the house wrap above. The nail flange is sealed with a blue skin on both sides, leave the bottom for drainage.
So if I explained it right you can see the whole system is to move water out and away from the structure.

On the inside you should end up with a 1/4" gap all aroud the window. That is closed with a 1/4 cord (round foam). Just pushed in about a 1/4 of an inch and sealed with a chaulk that is sold for that.
The other requirment we have is the cavity below the window between the studs. If the outside is plywood or solid anyway, we have to drill a 1 1/2" hole thru the plywood once in each cavity to allow evaporation of any water that does still find it's way in there.
__________________

Last edited by nealtw; 05-21-2013 at 11:18 PM.
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 05-21-2013, 11:20 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,754
Liked 928 Times on 828 Posts
Likes Given: 1596

Default

Almost forgot, expect all windows in the building to be installed the same way, so If I am right about this one??

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 05-23-2013, 09:34 PM  
condoowner
Senior Member
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

Thanks nealtw for replying.

The building here is 8 years old. Talking to the strata, they never re-caulked the windows and doors, and I was under the impression that caulk had to be replaced (or re-pointed) about every 5 to 6 years. If true, then ours is overdue. When I purchased this condo, the home inspector mentioned that caulking should be inspected periodically and replaced or re-pointed if needed but did not mention that it had to be redone right away. I just looked at it, and nowhere I can see it peeling off or cracking. Its still soft and flexible like silicon caulk.

That being said, there is definitely a problem here with my window. The original builder is coming either tomorrow or Monday to look at the issue. In the meantime, I have removed the window trim and enlarged the gap between the window sill (wood that I punched thru) and the drywall. I can see the vapor barrier edge but nothing else.

I really curious to see the wall's inside when the guy comes in. I certainly hope this is a new leak and that no real severe damage has happened. I put some more caulk outside where the "possible" failure of the caulk could have happened. Since sunday, the hole has been kept open and left to dry. Now its almost dry. Ive drilled a second hole about 4 inches away from the first one and it was completely dry. About 2 feet on the left of the wet spot, theres the electrical main which is enclosed in a small "closet" style enclosure which exposes the vapor barrier and the studs. All is fine there. So I imagine that if there are any damage, its confined to a 3ft portion of the wall...

I read about this "leaky condo syndrome" on the internet. First time I heard about it. Its scary and owners are completely left on their own.

IMG_0902.jpg   IMG_0904.jpg  
__________________
condoowner is offline  
 
Reply With Quote Quick reply to this message
Old 05-23-2013, 11:25 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,754
Liked 928 Times on 828 Posts
Likes Given: 1596

Default

The problem isn't rain getting in, it's condensation not getting out. Our code included rain screening in 2006 and I don't know when you would have had it but likely after your place was built.
The vapour bearer is to stop warm moist air from getting to the insulation. As the window has the lowest R value, the bearer is most important in that area. As it didn't wrap to the out side, that's your source of water. So you can give him a bad time about that. If they do pull the window make sure you know what the newest code is there and insist they follow it. They can't be trusted, you can see how they installed the bearier.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 05-24-2013, 07:06 AM  
condoowner
Senior Member
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

I totally agree with you.

however the big question is: who will have to pay for that ??

If what you are saying is true , I would think this qualifies more as a defect of craftsmanship during constructions and not something that deteriorated over time like roof shingles. ..

I can already hear them scream out loud that the home warranty is over. I dont think the waranty has anything to do with this. Because they didn't follow the code at construction time I believe they have to fix everything themselves.

I called the quebec ministry of buildings. Like every other ministries here, they were not of any help and they redirected me to various sources. In the end this province protect dishonest people and thieves.. im worried somehow we end up spending 50k to redo all windows..

__________________
condoowner is offline  
 
Reply With Quote Quick reply to this message
Old 05-24-2013, 08:08 AM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,754
Liked 928 Times on 828 Posts
Likes Given: 1596

Default

Alot of ours were covered under warrentee. The warrentee companys went broke.

__________________
nealtw is offline  
 
Reply With Quote Quick reply to this message
Old 05-24-2013, 09:15 AM  
condoowner
Senior Member
 
Join Date: Dec 2009
Posts: 135
Liked 6 Times on 6 Posts
Likes Given: 10

Default

I will wait for the buidler's contractor to open up the wall and then I'll take some pictures as evidence. If the windows were not installed properly and damage happened, most likely I will talk the strata into initiating a lawsuit against the builder for wrongdoing and failing to meet the code's requirements at the time of construction. On top of that, if there is mold or anything that can harm human health, there will be another lawsuit for this.

I dont see any difference between this and a car manufacturer who would fail to design a braking system that would not be able to stop the car and death or mutilation would occur as a result of this..

Only the "brake" analogy would happen much faster than home deterioration but in my opinion the essence is the same.



__________________

Last edited by condoowner; 05-24-2013 at 09:17 AM.
condoowner is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Is this mold? ws669 General Home Improvement Discussion 7 01-20-2012 03:49 PM
HELP!!! I have mold V92C General Home Improvement Discussion 3 02-15-2010 09:11 PM
New to Mold moldgirl Introductions 4 11-11-2009 02:14 AM
Mold or What jlwelding General Home Improvement Discussion 1 06-22-2009 05:47 PM
Is this MOLD? kc2651 General Home Improvement Discussion 9 01-18-2008 01:29 PM

Newest Threads

LATEST SPONSOR DEALS