DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > soffit vent ?




Reply
 
Thread Tools Search this Thread Display Modes
Old 05-23-2013, 10:24 AM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 268
Liked 96 Times on 81 Posts

Default soffit vent ?

Hi folks,
I have an enclosed 10' x 20' patio with a flat, pitched roof. It has a 24" overhang. Constructed with 3x6s, 16" oc. that is scabbed onto a hip roof.
I tore out and replaced the soffit boards and was going to replace the soffit vent but realized that the rafters are cross-blocked in at about 26" in from the tail ends.
Obviously this prevents any "venting" of the roof.
I live in SW Florida and I'm wondering if having a vent is even needed on this roof.
Thanks,



__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 05-23-2013, 12:51 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,231
Liked 116 Times on 101 Posts
Likes Given: 65

Default

What is on the roof (corrugated panels, asphalt shingles, EPDM)?
How many rows of 'cross-block' are beyond the first set?
Were the old panels ventilated?



__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Old 05-23-2013, 02:36 PM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 268
Liked 96 Times on 81 Posts

Default

The roofing material is rolled. Each of the bays is blocked. I don't don't know if there are other cross blocks deeper in. The ceiling in the space is plywood.
The old panels were vented but so was a 10' section that consisted of 24" lookouts at right angles to the rafters.
I have a feeling that they installed the vents because they thought they should, not because that actually needed to.
The rest of the house is covered with a hip roof and the 24" overhang is vented, as it should be.
Thanks,

__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 05-31-2013, 07:37 AM  
WindowsonWashington
Junior Member
 
WindowsonWashington's Avatar
 
Join Date: May 2013
Location: Washington, DC, Virginia
Posts: 198
Liked 19 Times on 18 Posts
Likes Given: 28

Default

Should be vented in an ideal world.

Can you locate exhaust venting in the middle of the roof? Can you cut a cross over in the cross blocks?

__________________
WindowsonWashington is offline  
 
Reply With Quote Quick reply to this message
Old 06-01-2013, 04:50 PM  
GBR
Senior Member
 
Join Date: Mar 2009
Posts: 348
Liked 23 Times on 22 Posts
Likes Given: 9

Default

I wouldn't add more because you could get other problems. You may get a 10% reduction of ceiling flux (from 1/300 to 1/150) but an 8% increase in relative humidity for the wood framing comes with it; pp. 7;
http://www.google.com/url?sa=t&rct=j...mH81PA&cad=rja

Is there any insulation in this thin cathedral ceiling? Is there conditioned space below the plywood, or another attic space?

Gary
PS. 24" overhang doesn't require venting if exterior to attic space.

__________________

Last edited by GBR; 06-01-2013 at 04:52 PM.
GBR is offline  
 
Reply With Quote Quick reply to this message
Old 06-02-2013, 10:24 AM  
beachguy005
Senior Member
 
Join Date: Sep 2012
Posts: 268
Liked 96 Times on 81 Posts

Default

Code:
Can you locate exhaust venting in the middle of the roof? Can you cut a cross over in the cross blocks?

Given that it's a flat roof and I have no access, I don't think I'd do that.


Code:
 Is there any insulation in this thin cathedral ceiling? Is there conditioned space below the plywood, or another attic space?
There is no insulation that I can tell. The space below has not been conditioned. It was a partially screened florida room with 16 foot sliders going into the house. It's now remodeled, totally enclosed and I'm hoping to remove the 16' sliders and open the space into the house.
I don't know if my ac unit can handle the additional 200 sqft. Nor do I know how much radiant heat I'll be getting into the room from this ceiling.
__________________
beachguy005 is offline  
 
Reply With Quote Quick reply to this message
Old 06-02-2013, 11:27 AM  
WindowsonWashington
Junior Member
 
WindowsonWashington's Avatar
 
Join Date: May 2013
Location: Washington, DC, Virginia
Posts: 198
Liked 19 Times on 18 Posts
Likes Given: 28

Default

If its not conditioned, don't worry about it.

If you decide to condition it, you could furr the ceiling down and insulate with rigid board if need be.

__________________
WindowsonWashington is offline  
GBR Likes This 
Reply With Quote Quick reply to this message
Old 06-03-2013, 08:44 PM  
GBR
Senior Member
 
Join Date: Mar 2009
Posts: 348
Liked 23 Times on 22 Posts
Likes Given: 9

Default

http://www.buildingscience.com/docum...n-roof-venting

Gary
__________________
GBR is offline  
 
Reply With Quote Quick reply to this message
Old 06-03-2013, 09:22 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,998
Liked 967 Times on 860 Posts
Likes Given: 1653

Default

having a bad day



__________________

Last edited by nealtw; 06-03-2013 at 11:31 PM. Reason: posted in wrong thread
nealtw is online now  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Best kind of soffit vent? jfm General Home Improvement Discussion 3 11-05-2011 07:50 AM
Replacing rotted soffit JTGP Roofing and Siding 4 10-12-2011 07:49 PM
Bathroom exhaust fan. Is it ok to vent it through attic & up to ridge vent? lola123go General Home Improvement Discussion 9 05-13-2010 04:58 PM
Facia and Soffit Bull40 Roofing and Siding 1 07-02-2008 06:13 AM
replacing a soffit rmaybon Roofing and Siding 2 09-06-2007 05:57 PM

Newest Threads

LATEST SPONSOR DEALS