DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > adhesive for tile shower floor and what type of mortar




Reply
 
Thread Tools Search this Thread Display Modes
Old 11-07-2013, 05:21 PM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default adhesive for tile shower floor and what type of mortar

hello all, haven't posted in awhile. planning on doing a tile shower floor. have two questions. what type of mortar for the shower pan. and what type of adhesive to use for the tiles. thanks



__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 11-07-2013, 05:24 PM  
oldognewtrick
Moderator
HRT_MODERATOR.png
 
oldognewtrick's Avatar
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 5,681
Liked 493 Times on 410 Posts
Likes Given: 150

Default

What type of tile are you using and what about the shower pan? How are you planing on making a water tight seal against the wall Are the wall tiles being replaced also?



__________________
oldognewtrick is offline  
 
Reply With Quote Quick reply to this message
Old 11-22-2013, 11:00 AM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default

will be ripping out old tile wall and replacing vinyl shower pan. just want to know what type of mortar to use for the shower pan. thanks

__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 11-22-2013, 01:49 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,292
Liked 403 Times on 314 Posts
Likes Given: 166

Default

Your typical meu pan is made with clean sand, portland cement and water. That’s it! Nor magic!

Don’t consider adding anything else. The basic recipe is 5 parts sand to 1part portland cement — 5:1. Some professionals prefer a richer mix of 4:1, but I’ve found that ratio hard to mix and spread. Too much cement and the mortar tends to clump as you mix it. Other pros advocate a 6:1 or even a 7:1 recipe. I think 5:1 can be considered the median of the industry. I think it’s ideal. Richer or leaner mixes do the job, though, so don’t panic if your mud is not “ideal.”

Properly smoothed and sloped, this pan is great for your tile floor. You should coat the pan with an elastomeric product like Red Gard or Dragon Shield for water proofing. Adhere the tile with THINSET.

Have fun

__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Old 11-22-2013, 02:07 PM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default

thanks. do I need to know what thickness tile I'll be using before this, or is the drain adjustable after the mortar is installed?

__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 11-22-2013, 02:27 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,292
Liked 403 Times on 314 Posts
Likes Given: 166

Default

You have to set the drain to the projected finished floor of the shower, excluding the thickness of the tile.

Do you know how to set the drain? It is the most important thing you do because once the pan is set, it is not fixable.

Watch this video for many good ideas ...

__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Old 11-23-2013, 08:07 AM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default

thanks for the video. But I have another question. he says that the thickness of his mortar is 2.25-2.5 thickness at the wall. my shower will be only 2 foot wide. that's a pretty thick floor for my space. is there a way to figure out how thick my floor should be? thanks

__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 11-23-2013, 09:15 AM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,292
Liked 403 Times on 314 Posts
Likes Given: 166

Default

You're really making me push that rock uphill ...

The minimum pitch of the floor should be somewhere between 0.3" - 0.375" per linear foot of shower radius. This applies to larger showers which assumes a 2.5" outside thickness. The last shower I did was about 2" ...

I would think a minimum of 1.25" - 1.5" thickness would suffice for your project. Remember, this is the bas which will carry the weight of your tile and body.

__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Old 11-23-2013, 11:48 AM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default

thanks again for your advice. just want to get this right the first time.

__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Old 12-05-2013, 11:48 AM  
sisyphus
Senior Member
 
Join Date: Apr 2011
Location: orange county, ny
Posts: 129
Default

took out the shower pan and discovered cement board in place. can I just pour the new stuff onto this surface and do I still need to install metal lath in the preslope. thanks again.



__________________
sisyphus is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
tile shower floor sisyphus Plumbing Forum 0 04-03-2012 07:52 AM
Shower Floor Re-Tile CallMeVilla Flooring 8 10-17-2011 06:30 PM
How to tile over old vinyl-tile adhesive? burgie Bricks, Masonry and Concrete 5 08-25-2010 05:26 PM
Cheap vinyle tile adhesive removal? s2horn Flooring 4 07-28-2008 09:50 AM
self-adhesive tile on paint? linneak Flooring 2 07-05-2006 12:53 PM

Newest Threads

LATEST SPONSOR DEALS