DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > leveling toilet on pebbled floor




Reply
 
Thread Tools Search this Thread Display Modes
Old 02-23-2014, 02:20 PM  
greenlady0
Member
 
Join Date: Oct 2011
Location: Cleveland, Ohio
Posts: 30
Liked 1 Times on 1 Posts

Default leveling toilet on pebbled floor

Any tips? Just underwent a bathroom redo extended the riverstone/pebble flooring from shower into rest of small bathroom. Problem now is finding a way to level older toilet over the stones any ideas appreciated.



__________________
greenlady0 is offline  
 
Reply With Quote Quick reply to this message
Old 02-23-2014, 03:03 PM  
nealtw
Contractor
 
Join Date: Nov 2010
Location: vancouver, b.c.
Posts: 10,975
Liked 963 Times on 856 Posts
Likes Given: 1648

Default



__________________
nealtw is online now  
 
Reply With Quote Quick reply to this message
Old 02-24-2014, 11:51 AM  
greenlady0
Member
 
Join Date: Oct 2011
Location: Cleveland, Ohio
Posts: 30
Liked 1 Times on 1 Posts

Default

Thanks that should work.

__________________
greenlady0 is offline  
 
Reply With Quote Quick reply to this message
Old 02-24-2014, 01:13 PM  
havasu
on permanent vacation
HRT_LIFETIMESUPPORTER.png
 
havasu's Avatar
 
Join Date: Oct 2010
Location: Southern California, CA
Posts: 2,367
Liked 120 Times on 100 Posts
Likes Given: 35

Default

If you decide to caulk for stability, make sure you caulk only the left, right and front sides of the toilet, but leave the back open so as to alert you if and when the wax ring fails you.

__________________
havasu is offline  
 
Reply With Quote Quick reply to this message
Old 02-24-2014, 01:45 PM  
Wuzzat?
Banned
 
Join Date: Jan 2010
Posts: 2,328
Liked 167 Times on 154 Posts
Likes Given: 94

Default

I guess people sitting on toilets and getting up again is considered to be an "impact load". For sure it's not a "static load" so I'd use epoxy with these shims so they don't work themselves out over time.

__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 02-24-2014, 02:39 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,229
Liked 116 Times on 101 Posts
Likes Given: 65

Default

Find the high spots and grind them down with a masonry grinding wheel.

__________________
kok328 is offline  
nealtw Likes This 
Reply With Quote Quick reply to this message
Old 02-24-2014, 03:06 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,309
Liked 408 Times on 318 Posts
Likes Given: 171

Default

I am very uncomfortable with this approach. The point load along the outside rim of the toilet will hit unevenly. The result could be cracking of the toilet. Not good.

You are better off laying down a QuickSet generously thick border around the circumference of the toilet rim at the maximum height of the pebbles. Use a double wax ring or extension to lift the connection. Obviously, you want long hold down bolts for the toilet and cut off the excess.

Lay the pebble sheets close to the rim but hold them back a bit. Lay individual pebbles to close the gap between the pebbles and the bottom rim. Caulk the final gap in the front and sides. Leave the back open (no caulk) in case there is ever a leak.

__________________
CallMeVilla is offline  
2
People Like This 
Reply With Quote Quick reply to this message
Old 02-25-2014, 08:03 AM  
SewerRatz
Junior Member
 
Join Date: Feb 2014
Posts: 8
Liked 2 Times on 2 Posts
Likes Given: 1

Default

  • Place the water closet (W/C, toilet) on the flange without any seal.
  • Make sure it is square, then trace an outline of the W/C onto the floor.
  • Remove the W/C, and set to the side. Now take some plumbers putty and make a rope about 3/4" think and place on the inside of your traced marks, and gently flatten it by hand.
  • Now place what you are using for a seal, and set the W/C.
  • Apply all your weight on the W/C and gently rock it to compress the seal and the putty.
  • Now tighten very evenly the closet bolts. Once secure, cut away excess putty.
  • Do not caulk at this time, after a few days use, check the closet bolts for tightness, now you may caulk if you want.
__________________
SewerRatz is offline  
nealtw Likes This 
Reply With Quote Quick reply to this message
Old 02-25-2014, 10:01 AM  
Wuzzat?
Banned
 
Join Date: Jan 2010
Posts: 2,328
Liked 167 Times on 154 Posts
Likes Given: 94

Default

Hardened plumber's putty can support weight without cracking? How quick does it harden?

"tighten very evenly the closet bolts"
while checking for level.

__________________
Wuzzat? is offline  
 
Reply With Quote Quick reply to this message
Old 02-25-2014, 02:24 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,309
Liked 408 Times on 318 Posts
Likes Given: 171

Default

Uh, Ratz? That is a nice progression ... but how do you account for the pebbles? Or, is this just a way to set a toilet on a standard surface?

Call me a bit "confused."



CONFUSED.jpg  
__________________
CallMeVilla is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Leveling a floor with foam? Jungle Flooring 5 09-25-2013 09:06 PM
Warped floor joists, floor leveling Jungle Flooring 25 08-16-2013 07:31 AM
Leveling bathroom floor mozingod Flooring 9 04-07-2011 04:50 AM
Leveling bathroom floor Willieb18 Framing and Foundation 8 01-20-2010 09:27 PM
Leveling Garage Floor YADAX3 General Home Improvement Discussion 2 04-14-2007 09:07 AM

Newest Threads

LATEST SPONSOR DEALS