DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Electrical and Wiring > How hard is it to switch plugs?




Reply
 
Thread Tools Search this Thread Display Modes
Old 02-19-2007, 09:08 AM  
WestBentley
Member
 
Join Date: Dec 2006
Posts: 37
Default How hard is it to switch plugs?

How hard would it be to unhook and replace the plugs in the walls - not the whole box, but the part you see through the cover? Our plugs may have once been white but are definitely yellowed looking and I want to replace all the outlet covers and actually plastic plugs so they'll match the white trim in the rooms instead of looking dirty. I've got zero electrical experience, but my fiance knows enough to replace light fixtures without incident, so I'm guessing he could do this and probably show me how as well? Any website w/how-to's would be appreciated, I'm trying to be a Ms. Fixit rather than a Ms. Wait for the Man to Fixit!



__________________
WestBentley is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 12:01 PM  
CraigFL
Senior Member
 
Join Date: Mar 2006
Posts: 409
Default

Usually this is easy BUT.... there can be some problems, especially with older wiring where there can be no extra ground wire or return ground path. As long as you replace with a standard 3 prong outlet and you have white, black and ground wire, it will be very easy.



__________________
CraigFL is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 12:03 PM  
WestBentley
Member
 
Join Date: Dec 2006
Posts: 37
Default

The house was only built in '88, so I'm pretty sure the wiring is standard. Glad to hear it might be easy. Aaron is the big picture guy, but I want the details to be right!

__________________
WestBentley is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 01:29 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

Use a tester to make sure the power is off (at the breaker panel) to every receptacle before you start each one!!

Black or red wires should always be attached under brass screws, or in stablocks on the brass side.

White wires should always be attached under the silvery screws or in the stablocks on the silvery side.

Ground, green or bare copper wires should always be under the green screws near the ends of the receptacle.


If the wires are currently attached in the stablocks in the back of the receptacle, you will need a small screwdriver to release them.
Place the small screwdriver in the slot near the wire and apply pressure while pulling the wire out.
Other wise they can break off from trying to rip them from the binds.


It's not hard, but it can get you burned, hurt, nearly blinded from flash, or killed.
Use a tester to make sure the power is off (at the breaker panel) to every receptacle before you start each one!!
__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 01:33 PM  
WilliamC
Junior Member
 
Join Date: Feb 2007
Posts: 5
Default

Once you pull the outlet out you can see how it's wired. Usually it's white to the silver colored screws and black to the brass colored screws. The green screw ( or one off to the metal side) is ground. Just make sure you have the power shut off to the outlets before hand. If you don't know what you are doing the whole job should take about 2 minutes per outlet, and about 1.5 minutes if you do know what you are doing. It's that easy. The last house I had had several bad outlets so i went ahead and spent about $35 and replaced every outlet and most of the covers in the whole house. It took me about an hour to do the entire house ( i did this just as i was moving in and cut power from the Main).

__________________
WilliamC is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 03:32 PM  
Kerrylib
Senior Member
 
Join Date: Jul 2006
Posts: 157
Default

Good description Square Eye.

Replacing an outlet should be something most anyone can accomplish. Make SURE the power is off before you go poking around.

Browse through some of the wiring how to books. Many have good pictures of how the outlets are to be wired. Good to know before you start, just in case the first one you open up is wired backwards or you pull the wires off and don't get them wired back on immediately.

When you look at the plug face, notice the slots are different sized. The bigger one is the neutral (white wiere, silver screw), the smaller slot is hot (black or maybe red wire, brass screw) and the D shapped one is ground (green or bare wire, green screw).

One good suggestion I've seen (specifically for metal boxes) is to put about two wraps of black electrical tape around the outlet to cover the screws before pushing the outlet back into the box. Prevents shorts to the box if the outlet shifts any or isn't squared up inside the box.

Also, a good practice for safety reasons is to install the outlet with the ground pins up. If the plug is not seated fully, there will be a small gap where things could slip behind the plug and contact the prongs. If you had something like a metal framed picture on the wall above this plug that happened to fall down, it might slip in that space and short out the plug. With the ground prong at the top, this scenario would lead to the metal picture frame landing on the ground prong. Similarily if the outlets are horizontal, mount them so the wide (neutral) side is on top.

__________________
Kerrylib is offline  
 
Reply With Quote Quick reply to this message
Old 02-19-2007, 07:15 PM  
inspectorD
Housebroken
HRT_MODERATOR.png
 
inspectorD's Avatar
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,091
Liked 125 Times on 105 Posts
Likes Given: 318

Default Good point Kerrylib

I have done a little welding with wires and outlets myself. That would be the Flash Square Eye talked about....

Any time I change outlets on a job, I have the electrician....they won't let me touch wires anymore.....install the outlet with the grounded D slot on the top.

My electrician once found a loose plug with a metal curtain drapery pull chain...the hard way, when he went to open the drapes.....

Seems the metal was resting on one of the hot legs and he was the ground.

Moral...don't go around pulling open other peoples drapes.

__________________

Just My
Made in the

inspectorD is offline  
 
Reply With Quote Quick reply to this message
Old 03-10-2007, 12:59 PM  
cjtursi1
Junior Member
 
Join Date: Mar 2007
Posts: 3
Default

All good tips and heres is another.The best connection is to bend a hook in the end of the wire and place it under the screw head.Stablock connections will not carry a larger load as it does not have as much surface area at the contact point.

__________________
cjtursi1 is offline  
 
Reply With Quote Quick reply to this message
Old 03-10-2007, 03:08 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

The hook is the way I wire receptacles too but, if the stablock is approved by Underwriters Laboratory, you can bet the ranch its safe. If they rate it for 15 amps, then the stablock will carry 15 amps.
I have had considerable experience with Underwriters Laboratory and have complete confidence in their testing.
Glenn

__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Old 03-27-2007, 10:31 AM  
WestBentley
Member
 
Join Date: Dec 2006
Posts: 37
Default

Follow up question to this - how do we know which type of plugs to buy? We were browsing the electrical section and there were about 3 types of plugs that appeared to be the same on the surface - 3 pronged holes, etc. But they were 'back wired' or some other names. What type of plug does a residential home typically use?



__________________
WestBentley is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Changing Switch to Recptacle SavvyCat Electrical and Wiring 2 01-04-2009 06:28 PM
Trane XE90 Pressure switch code. Truth? showngo2000 HVAC 7 10-13-2008 05:26 PM
Ceiling fan with 4 way switch. gan_nair Electrical and Wiring 4 08-13-2008 07:12 PM
Illuminated wall switch glows but bulbs won't light Paul in Maryland Electrical and Wiring 3 10-21-2007 09:34 AM
Dinning room switch Blair1955 Electrical and Wiring 9 06-22-2007 06:25 AM

Newest Threads

LATEST SPONSOR DEALS