DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Windows and Doors > Header for new patio door




Help Support House Repair Talk by donating using the link above.
Reply
 
Thread Tools Search this Thread
Old 05-07-2007, 02:40 PM  
maritadavis
Junior Member
Join Date: May 2007
Posts: 3
Default Header for new patio door

We have a garage attached to our house, but no doorway into it. We want to put a patio door in but discovered that the garage floor is 20 inches below the housefloor. In the garage, the height from the concrete floor to the rafters is only 100 inches, thus there would only be 80 inches left for a door, and this is the smallest rough opening for standard doors that I've been able to find. Marvin windows can make me a custom door of 6 foot 1 that would leave me about 4 inches for a header. Would a 4-inch I-beam be enough to support the load above a five-foot wide opening?

Yes, I realize that people will be bumping their heads but the house has such an odd design, it's all we can manage right now.


maritadavis is offline  
 
Reply With Quote
Old 05-07-2007, 03:19 PM  
glennjanie
Senior Member
Join Date: Mar 2006
Posts: 2,990
Liked 4 Times on 4 Posts

Default

Welcome to the Forum, Marita Davis:
If I understand your situation correctly, there should be an open wall on the house above the garage roof and space above the door inside. You could cut into the wall on the inside, put cripple studs on each side of the door opening and a double 2 X 8 or 2 X 10 across the top of the opening to support the wall. Then you could use the standard door with 80" opening, OR you could cut one or two steps into the house floor and get the head space up to code. The later fix would be very labor intensive but it wouldn't cost an arm and a leg for materials.
Glenn


glennjanie is offline  
 
Reply With Quote
Old 05-07-2007, 03:39 PM  
maritadavis
Junior Member
Join Date: May 2007
Posts: 3
Default

I think I understand what you're saying. Yeah, there is a wall above it. I'm printing this off and showing it to the handyman who is helping me.
maritadavis is offline  
 
Reply With Quote
Old 05-15-2007, 08:22 AM  
maritadavis
Junior Member
Join Date: May 2007
Posts: 3
Default Still need advice

What I discovered is that there is space on the internal wall for a header for the roof above the internal space. However, I still need support for installing a standard patio door. The height would be 80 inches, the width 60 inches. Is there anyway to find out whether an S4 x 9.5 I-beam would be strong enough to serve as the header? Is there a general rule of thumb of converting strength between I-beam headers and say, headers made by two 2x6"s.

I also have another support beam made up of 2 2x10s that spans 18 feet that I'd like to replace with an I-beam or maybe a laminate. Can anyone help me on calculating what I'd need?
maritadavis is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Hallway header options where door is infidex Walls and Ceilings 1 05-18-2013 04:48 AM
Door header and trim thickness matt_vo Decorating and Design 5 07-19-2012 12:48 PM
garage door header butcher757 Framing and Foundation 6 09-10-2008 08:50 AM
Header strength over garage door? the spindoctor Framing and Foundation 6 04-30-2008 05:23 AM
Header over 10-12' patio door gregoryedgar General Home Improvement Discussion 7 06-05-2006 02:52 PM



Newest Threads