DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Trying to remove walls to make a room bigger (floor plans inside)




Help Support House Repair Talk by donating using the link above.
Reply
 
Thread Tools Search this Thread
Old 11-18-2007, 12:29 AM  
ElementalWindX
Junior Member
Join Date: Nov 2007
Posts: 2
Default Trying to remove walls to make a room bigger (floor plans inside)

Here is a before and after pic of what I want to do to the bottom floor of my house. House was built in 1998, and is 2 stories. I am curious as to how I can tell if the walls I want to remove are load bearing or not. Anybody able to help me out with this? Thanks.


Click image for larger version

Name:	1st_floor_modified2.jpg
Views:	448
Size:	61.0 KB
ID:	380   Click image for larger version

Name:	1st_floor_unmodified2.jpg
Views:	365
Size:	65.2 KB
ID:	381  
ElementalWindX is offline  
 
Reply With Quote
Old 11-18-2007, 10:53 AM  
glennjanie
Senior Member
Join Date: Mar 2006
Posts: 2,990
Liked 4 Times on 4 Posts

Default

Welcome ElementalWindX:
The only way you can tell for sure if a wall is load bearing is to look in the attic. Your house being built in 1998 probably has roof trusses which means none of the upper floor walls are load bearing. The trusses will bear the load from outside to outside walls.
The first floor is a different story; the wall next to the garage is most likely a bearing wall, especially if they used dimensional lumber for floor joists on the second floor. It is possible that they used floor trusses that can give a clear span also. If it has floor trusses, you will need to find the source of them and ask the manufacturer if they are 'clear span' rated. In either case the walls limitiing your Living room typically would not be load bearing. The Hallway and Extra Closet walls will not be load bearing if the joists run right to left on your drawing.
Glenn


glennjanie is offline  
 
Reply With Quote
Old 11-26-2007, 06:48 PM  
ToolGuy
Senior Member
 
ToolGuy's Avatar
Join Date: Nov 2007
Posts: 482
Liked 2 Times on 2 Posts

Default

Looking at that drawing, I'd say the bearing wall is the one running full length right down the center.
__________________
~ ToolGuy ~

Save money on tools at MyToolbox.net
ToolGuy is offline  
 
Reply With Quote
Old 11-26-2007, 07:03 PM  
Hack
Senior Member
 
Hack's Avatar
Join Date: Nov 2007
Location: Petaluma, CA
Posts: 194
Liked 3 Times on 3 Posts

Default

My suggestion would be to contact a structural engineer and have them come over and take a look. They'll know right away what would need to be done. Many of them will do the "quick review" free of charge hoping that they'll get the calc work out of it.

Cheers, and good luck!
__________________
Hack (a.k.a. Jeff)
Hack is offline  
 
Reply With Quote
Old 11-29-2007, 06:56 AM  
inspectorD
Housebroken
HRT_ADMIN.png
 
inspectorD's Avatar
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,490
Liked 265 Times on 209 Posts
Likes Given: 772

Default So many posts...

Load bearing walls need to be evaluated by someone who is experienced...and actually standing in the house. That is the easiest, safest way to figure out if you have a load bearing wall. Within a structure you never know where a point load is. Something else could be carrying the weight of something it was never designed to carry.Then you remove it and the rest is a hospital memory...or worse.
This comes from over 25 years of experience as a high end re modeler of antique homes. And as a licenced home inspector and educator around the country. It is not that I know it all...But I do know what not to do, that is telling someone over these forums what to look for in a bearing wall. I might as when tell you how to change your electrical service while we are at it.

I am not trying to create an issue with this subject, I just remember covering this issue so much that we all should be on the same page.

You need an engineer , or other licenced , educated professional.

Climbing down from soapbox.....thanks for listening.


__________________
Just My
Made in the
inspectorD is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
How to make a dark room llok bright Justinkemp Walls and Ceilings 4 04-02-2013 08:14 AM
Copper Sillcock Broke off inside Brick Wall- How to remove? amodoko Plumbing Forum 11 12-02-2012 09:51 PM
Can I make my pantry walls narrower? terry47 General Home Improvement Discussion 5 08-08-2011 08:11 AM
Watermarks on inside of the room mighael Walls and Ceilings 1 01-28-2011 08:53 AM
Help me make my new room AWESOME! AndrewTheC General Home Improvement Discussion 3 12-13-2010 06:41 PM



Newest Threads