DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > Opening a wall




Reply
 
Thread Tools Search this Thread Display Modes
Old 12-21-2008, 10:21 PM  
1989gta
Junior Member
registry_dropdown_2318_26203
 
Join Date: Oct 2006
Posts: 24
Default

thanks for the advise
I went into the attic today and the roof rafters come to a V right above that wall. The rafters overlap and sit right on the top plate of that wall. Looks like i'm going to have to support both sides when i cut the wall out. for the beam support i plan on doubling a some studs and for the beam to rest on.


__________________
nick
1989gta is offline  
 
Reply With Quote
Old 12-21-2008, 11:40 PM  
glennjanie
Senior Member
registry_dropdown_630_26204
 
Join Date: Mar 2006
Posts: 2,990
Liked 3 Times on 3 Posts

Send a message via AIM to glennjanie
Default

Hello Nick:
OK now we know what we're up against. There should be 3 studs at each end to support the beam. And yes, it is wise to support both sides temporarily.
Glenn


glennjanie is offline  
 
Reply With Quote
Old 12-22-2008, 02:38 PM  
1989gta
Junior Member
registry_dropdown_2318_26216
 
Join Date: Oct 2006
Posts: 24
Default

good to know tomorrow i'll contact some lumber yards to see if i can get some beam pricing and specs.
__________________
nick
1989gta is offline  
 
Reply With Quote
Old 01-29-2009, 02:35 PM  
erndog
Member
registry_dropdown_5744_27326
 
Join Date: Feb 2008
Location: nashville, TN
Posts: 33
Liked 1 Times on 1 Posts

Default I did the same earlier

Hi I did the same project a few years ago. I have a 1 story house and the wall was load bearing. A local lumber yard had a computer program to calculate the spec's of the beam needed. I went with 2 2x12 laminated beams nailed and glued together. I rented jacks from a rental store for each side to support ceiling while I replaced the beam. I supported the laminated beam on the I-beam in the basement with 4x4 thru holes cut in the floor. I drywalled the arch with plastic round over trim. I haven't had any cracking or settling issues with it.
arch 7.jpg   arch 21.jpg   primed 003.jpg  
erndog is offline  
 
Reply With Quote
Old 01-31-2009, 07:40 AM  
jdougn
Senior Member
registry_dropdown_1663_27356
 
Join Date: Aug 2006
Posts: 132
Liked 1 Times on 1 Posts

Default

Erndog,

Nice project! I really like the bull-nose corner bead. Thanks for posting picts too!
Doug


jdougn is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
opening a wall 1989gta Framing and Foundation 0 12-17-2008 09:24 PM
Opening wall, don't think it's load bearing? CZSteve Walls and Ceilings 8 01-15-2008 12:45 AM
Cutting An Opening In An Exterior Wall dbone Framing and Foundation 1 11-03-2007 11:34 AM
opening a shear wall tgd61 Framing and Foundation 4 07-25-2006 10:45 PM
make opening in load bearing wall? Carey7 Flooring 2 06-27-2006 12:09 PM

Newest Threads

LATEST SPONSOR DEALS