DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Leaky Toilet Fill Valve

Help Support House Repair Talk by donating using the link above.
Thread Tools Search this Thread
Old 03-03-2009, 01:55 PM  
Junior Member
Join Date: Mar 2009
Posts: 1
Default Leaky Toilet Fill Valve

Due to iron and minerals in our well water (I have a filter at the well), the toilet fill valves develop leaks fairly soon after replacing the fill valve kits. I used to be able to buy just the plunger washers and they were cheap; now I can only find the repair kits for $5 or so, when only the washers need replacing. When they leak, I find bits of rust and mineral stuck to the washers and the washers have become deformed to the point that they still leak after removing the chunks. Short of installing point-of-use filters at each toilet (4 in the house), I can't see a way to keep the chunks from impacting the fill valves. Does anyone know of a source of the washers alone? They're 1B1 Master Mark IV valves. Alternatively, is there a type of fill valve that's not so succeptible to this kind of leakage, or that would have more economical individual repair parts?

StanS is offline  
Reply With Quote
Old 04-14-2009, 09:51 PM  
Certified Lunatic
Redwood's Avatar
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887

Stan ditch those Junk fill valves and get a Fluidmaster 400A
Redwood is offline  
Reply With Quote
Old 04-15-2009, 12:52 AM  
Emperor Penguin
Nestor_Kelebay's Avatar
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts


I second Redwood's advice for two reasons:

1. The rubber diaphragms are available separately for the 400A (as well as the preceding 200A).

2. Most people aren't aware of this, but you can replace the top portion of the 400A almost as easily as you could with the old 200A. Just slide the retaining collar up, and give the top part of the 400A a good strong yank and it'll separate from the bottom portion that will remain in the tank. (obviously shut the water off to the fill valve before yanking the top off or you'll have a water geiser)
But, the advantage here would be that you can have a "spare" top portion that you can push onto the bottom portion of any toilet that's leaking, and then just clean the rubber diaphragm in the top portion you pulled off so that it's ready to go into service whenever the next toilet leaks. That is, you can have a spare "top portion" that you can replace within 60 seconds, and then clean the rubber diaphram in the top portion you pulled off in your spare time at a more convenient location, like a kitchen table.

StanS: You should be aware that all toilet fill valves (that I know of) work by using the water pressure itself to shut off the flow of water. It's the same system that's used on washing machine water mixing valves, and it's very reliable. However, it's also very sensitive to dirt getting into the area where the rubber diaphragm is. So, if it wuz me, I would see if I could fit a hose washer with an integral filtration screen, the same kind as is used on the water supply hoses to washing machines, into the connection at the bottom of your toilet's fill valve. I'd try to get the hose washers with the very fine mesh stainless steel screens. You should be able to find these at any appliance parts store.

Hose washers with the coarser brass wire screens are also available, but I'd opt for the finer mesh stainless steel wire screens in this case.

Last edited by Nestor_Kelebay; 04-15-2009 at 12:59 AM.
Nestor_Kelebay is offline  
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Toilet Fill Valve kok328 Plumbing Forum 5 07-25-2013 11:07 PM
Toilet will not fill uziel Plumbing Forum 6 05-23-2013 03:28 PM
Slow toilet fill Daddytron Plumbing Forum 3 02-15-2012 09:06 PM
Water Fill Valve wholeteam Plumbing Forum 3 04-06-2010 04:36 PM
Leaky tank shutoff valve locknut Plumbing Forum 9 05-02-2009 12:05 PM

Newest Threads