DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Shower faucet maker/#?




Reply
 
Thread Tools Search this Thread Display Modes
Old 03-22-2009, 04:41 PM  
LuckyDad
Junior Member
registry_dropdown_13631_28689
 
Join Date: Mar 2009
Posts: 2
Default Shower faucet maker/#?

Hello everyone. New member here, but I won't be a "one & done". Going to be doing a lot of work on my house, so I'll be in and out for a long time.

I have a quick shower faucet question. I bought my house 3 years ago, but it was built in 1982 (in New Hampshire). Recently, the shower faucet refused to go all the way back in. So, I tried taking the cartridge out. It was really, really stuck in there. Finally, after some vinegar and liquid wrench, I got it out.

I need to replace it, but when I brought it to Lowes, they didn't have anything remotely like it. It's not a stem sliding in a body type (can't get that lucky). It's a single piece of brass that's hollow and has strategically located holes with screens to align with the feed pipe entries inside the valve itself.

I have no idea who makes this thing. It wasn't on the knob or the estuchion. Nor is there anything written on the valve. I believe the valve is brass.

The feed lines are offset about 1.5 inches from the vertical run to the shower. It has two screw heads in line on the entries that look like they might shut the feed off.

Any suggestions? Thanks.


LuckyDad is offline  
 
Reply With Quote
Old 03-22-2009, 05:57 PM  
inspectorD
Housebroken
HRT_ADMIN.png
 
inspectorD's Avatar
registry_dropdown_391_28692
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,234
Liked 177 Times on 148 Posts
Likes Given: 440

Default Best bet

Take it to a plumbing supply house and take a picture along as well. Those guys know what parts go where. This is your best option.
Welcome.


__________________
Just My
Made in the
inspectorD is offline  
 
Reply With Quote
Old 03-27-2009, 01:24 PM  
LuckyDad
Junior Member
registry_dropdown_13631_28857
 
Join Date: Mar 2009
Posts: 2
Default

Well, file this under "Good News/Bad News? You Decide":

I took the faucet cartridge to the plumbing supply shop. The reason I'd never seen a faucet cartridge like this one... it's not the cartridge. It took them a while to figure out what I had handed them, but apparently, I do have a Moen 1200 series faucet. What I had in my hands... was the piston. I had ripped it out of the cartridge. Apparerently, the cartridge body is still embedded in the faucet.

This is good news in that "IF" I can get the body out (which is now a cylinder in a cylinder), I have the replacement. It's that tricky if part that's the rub.

I'm hitting it with liquid-wrench every ten minutes. But I'm afraid to apply too much torsion on the "ears" with the white plastic cap, as I've already broken one.

Any suggestions on getting the old cartrdige body out?

Thanks!
LuckyDad is offline  
 
Reply With Quote
Old 04-08-2009, 05:30 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
registry_dropdown_13814_29264
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

There is also a Moen single handle lever cartridge puller tool available if you have trouble getting the old cartridge out:



http://www.plumbersurplus.com/Prod/M.../55168/Cat/662

From what I can see, this tool allows you to both twist the cartridge (cuz of the hex on the tool) and pull on it at the same time. That SHOULD be more successful than either separately. And, given the size of the hex, you could turn it with a wrench and apply considerably more torque to the cartridge than you could with the plastic cap.

PS: For others in here with Moen single handle cartridges, this web site shows step by step instructions as well as multimedia movies for removing Moen single lever cartridges:
http://www.moen.ca/installation/moen...0133.cfm#watch

Last edited by Nestor_Kelebay; 04-08-2009 at 06:05 PM.
Nestor_Kelebay is offline  
 
Reply With Quote
Old 04-08-2009, 09:25 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
registry_dropdown_13814_29273
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

Yeah, I wrote that before I realized that he'd already broken one of those plastic cap wrenches trying to rotate that cartridge body.
Nestor_Kelebay is offline  
 
Reply With Quote
Old 04-13-2009, 06:40 PM  
Redwood
Certified Lunatic
 
Redwood's Avatar
registry_dropdown_14118_29380
 
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887
Default

Pasco Specialty makes one that works once the center stem has been pulled out...
Pasco P/N 7040 in the catalog I wish I could link below link below.
Silly rules make it difficult to help here...
There are better ways to fight spam
4 more posts and I'll stop grumbling...

Google pasco specialty
and click/ products / catalog / tools & Electrical C / it is in there
They are available at many plumbing supply companies...

Use the notched end to rotate the remaining part of the cartridge first then use the end with the button to pull the cartridge out.
This is a do or die tool!

Either the cartridge is coming out or the tool and cartridge are stuck and you are installing a new valve.
Redwood is offline  
 
Reply With Quote
Old 04-15-2009, 10:05 AM  
handyguys
Senior Member
 
handyguys's Avatar
registry_dropdown_5759_29521
 
Join Date: Feb 2008
Location: USA
Posts: 815
Liked 2 Times on 2 Posts

Send a message via Skype™ to handyguys
Default

Lucky - Did you get it out? My guess is that its not corroded in there but that its not aligned correctly to remove it or your doing something wrong. Maybe check with Moen for some documentation on how to remove the cartridge. They have good customer service.
__________________
The Handyguys Podcast [url]http://www.handyguyspodcast.com[/url]
handyguys is offline  
 
Reply With Quote
Old 04-15-2009, 10:27 PM  
Redwood
Certified Lunatic
 
Redwood's Avatar
registry_dropdown_14118_29544
 
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887
Default

Check out page 4 of the catalog linked below.
http://pascospecialty.com/catalog/PASCO_CATALOG_C.pdf

It is the Moen Cartridge removal tool I spoke of in the post above...
Redwood is offline  
 
Reply With Quote
Old 04-17-2009, 10:38 AM  
MACPLUMB
35 YEAR MASTER PLUMBER
registry_dropdown_14099_29595
 
Join Date: Apr 2009
Location: NORTH HOUSTON, TEXAS, T E X A S
Posts: 19
Default Shower faucet moen



go with the "pasco" tool it is cheaper to buy for your limited time
use around the house, and it works just as good as the moen tool
MACPLUMB is offline  
 
Reply With Quote
Old 04-17-2009, 08:40 PM  
NHMaster
Junior Member
 
NHMaster's Avatar
registry_dropdown_14125_29618
 
Join Date: Apr 2009
Posts: 8
Default

Here's what I use

Moen Strikes Again


sledge-hammer.jpg  
NHMaster is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Tub faucet leak when shower is on? sbattisti Plumbing Forum 31 09-01-2011 08:59 AM
Non-producing Ice Maker henfeather General Appliance Discussion 7 01-25-2009 08:24 PM
pressure balanced shower faucet Kath Plumbing Forum 1 01-05-2009 04:41 AM
outside faucet catlutz Plumbing Forum 5 08-25-2006 09:51 AM

Newest Threads

LATEST SPONSOR DEALS