DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > bathtub overflow??




Reply
 
Thread Tools Search this Thread Display Modes
Old 10-10-2009, 08:15 PM  
Rob99
Junior Member
registry_dropdown_16670_35537
 
Join Date: Oct 2009
Posts: 3
Default bathtub overflow??

Hi guys

I've just noticed that after my upstairs tub was used, the ceiling in my living room directly below was wet. The caulking is fine I'm suspecting it's the bathtub overflow because I'm told the tub was filled to the top and I think water got in there.

I took off the cover and it looks like the previous owner just tried filling the hole with caulking since there were globs in there.

Is it worth the hassle of fixing it properly which would probably include making a hole in the ceiling to gain access, or would you just seal off the overflow and make sure whoever uses that tub never fills it that high?

thanks.


Rob99 is offline  
 
Reply With Quote
Old 10-10-2009, 08:21 PM  
kok328
Supporting Member
HRT_SUPPORTER.png
registry_dropdown_4883_35539
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,326
Liked 145 Times on 123 Posts
Likes Given: 71

Default

I'd be willing to let it go. As long as the tub isn't filled to a point where if someone gets in it after filling it, the level would overflow onto the floor.


kok328 is offline  
 
Reply With Quote
Old 10-10-2009, 08:22 PM  
Cork-Guy
Cork Flooring Pros
 
Cork-Guy's Avatar
registry_dropdown_16612_35540
 
Join Date: Oct 2009
Posts: 243
Default

Well, if you can make sure no one uses it again that is a solution. However, are you sure it's the overflow? It could be another underlying problem and it might be worth checking it out and turning a future problem in a solution.
__________________
[B][URL="http://www.corkflooringpros.com"]Cork Flooring[/URL][/B] - [B][URL="http://www.ventless-fireplace.org"]Ventless Fireplace[/URL][/B]
Cork-Guy is offline  
 
Reply With Quote
Old 10-10-2009, 08:27 PM  
Rob99
Junior Member
registry_dropdown_16670_35542
 
Join Date: Oct 2009
Posts: 3
Default

Quote:
Originally Posted by kok328 View Post
I'd be willing to let it go. As long as the tub isn't filled to a point where if someone gets in it after filling it, the level would overflow onto the floor.
It is the guest bathroom and it's been used a total of once in the past 2 years. I'm leaning this way.

Quote:
Originally Posted by Cork-Guy View Post
Well, if you can make sure no one uses it again that is a solution. However, are you sure it's the overflow? It could be another underlying problem and it might be worth checking it out and turning a future problem in a solution.
The reason I think it's the overflow is because I couldn't recreate the leak. The leak happened last week. Yesterday I ran the water for about 10 mins and wet stains on the ceiling. I then filled the tub half way and let it sit for a while, then drained it. No wet stains on the ceiling.
I then removed the valve cover and ran the shower for 10 minutes to see if any water was leaking behind the wall. No leak.

The only thing left is the overflow I'm thinking.

thanks for the replies.
Rob99 is offline  
 
Reply With Quote
Old 10-11-2009, 07:27 AM  
Redwood
Certified Lunatic
 
Redwood's Avatar
registry_dropdown_14118_35551
 
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887
Default

Look at the overflow gasket in between the tub and overflow.
Another possibility is the screws on the overflow plate are loose.
Redwood is offline  
 
Reply With Quote
Old 10-11-2009, 09:18 AM  
Rob99
Junior Member
registry_dropdown_16670_35554
 
Join Date: Oct 2009
Posts: 3
Default

Quote:
Originally Posted by Redwood View Post
Look at the overflow gasket in between the tub and overflow.
Another possibility is the screws on the overflow plate are loose.
Looks like this is it.
There appears to be a small gap between the overflow pipe and the actual hole in the tub that's not caulked so rising water would seep through that crack before reaching the level of the overflow pipe. There's a gasket for this? I was thinking of just caulking that gap.
Rob99 is offline  
 
Reply With Quote
Old 10-11-2009, 02:36 PM  
Nestor_Kelebay
Emperor Penguin
 
Nestor_Kelebay's Avatar
registry_dropdown_13814_35562
 
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts

Default

Rob99:

I've replaced that beveled washer behind the overflow, and plumbers here in Winnipeg do it from inside the bathtub. You simply take the crossbar out and push the overflow drain pipe far enough back to slip the old gasket off and slip a new one on.

I'd like to hear what Redwood says on this, but I know for a fact that I've replaced that gasket without causing another leak at the joint where the tee where the overflow and drain pipes meet.

The gasket is a beveled type, very similar to the one that goes between a toilet flush valve and the toilet tank, only a little smaller.
Nestor_Kelebay is offline  
 
Reply With Quote
Old 10-11-2009, 06:26 PM  
Redwood
Certified Lunatic
 
Redwood's Avatar
registry_dropdown_14118_35571
 
Join Date: Apr 2009
Location: Olde Tyme, Connecticut
Posts: 887
Default

Yes Nestor that is how I do it as well unless there is already access from behind.
Many use a gasket like the one pictured below that is tapered.
The thin part goes to the top.



Some use a slightly different gasket that have 2 ears that clip over the waste and overflow like the one pictured below. Kohler I think is one that does.

Redwood is offline  
 
Reply With Quote
Old 11-07-2009, 02:46 PM  
Leontyne Lilibeth
Junior Member
registry_dropdown_16940_36510
 
Join Date: Nov 2009
Posts: 2
Default

I have a bathtub overflow plate that was removed. However the screws were so old that they snapped. I tried a pliers to remove them without any luck. Anyone have any other suggestions?
__________________
[url=http://www.sinksusa.com]stainless steel sinks[/url]
Leontyne Lilibeth is offline  
 
Reply With Quote
Old 11-07-2009, 06:24 PM  
travelover
Senior Member
registry_dropdown_4113_36513
 
Join Date: Aug 2007
Posts: 693
Liked 2 Times on 2 Posts

Default

Quote:
Originally Posted by Leontyne Lilibeth View Post
I have a bathtub overflow plate that was removed. However the screws were so old that they snapped. I tried a pliers to remove them without any luck. Anyone have any other suggestions?
Use a screw extractor or similar tool. It requires that you drill a hole in the middle of the broken off screw. Sometimes drilling the hole with a left hand drill will cause the screw to back out

Screw Extractors | Bolt Extractor | Square Easy Out | Spiral Easy Out

You might also be able to slot the stub with a small saw blade or Dremel wheel and back it out with a flat bit screwdriver.

How to Remove a Broken Bolt | eHow.com


travelover is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Crack in the bathtub mwilson Plumbing Forum 2 04-01-2009 10:39 PM
Correct pop-up assembly for Lav sink - no overflow jbutts Plumbing Forum 2 02-01-2009 03:57 PM
Replacing a bathtub morrigan3003 General Home Improvement Discussion 6 03-19-2008 12:10 PM
bathtub woodman1403 Introductions 2 01-11-2008 05:20 PM
Old Bathtub James Plumbing Forum 0 07-15-2005 11:43 PM

Newest Threads

LATEST SPONSOR DEALS