DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Carpentry and Woodworking > need help with cove cut angles




Reply
 
Thread Tools Search this Thread Display Modes
Old 07-08-2006, 05:01 PM  
Texasguy
Junior Member
 
Join Date: Jun 2006
Posts: 5
Default need help with cove cut angles

Help!!! I am attempting to install crown molding (38 degree) to a cathedral ceiling and I can’t seem to be able to figure out the angles for the corners where the side walls meet the end walls.
The ceiling goes up at a 10 degree angle along the end walls.
Adding to my troubles is the fact that I am mathematically challenged.
I have a 10" sliding compound miter saw, but havn't used it much up till now.
Can anyone offer any advice? (Other than to hire someone to come in and install the molding?)

Thanks in advance



__________________

Last edited by Texasguy; 07-08-2006 at 05:04 PM.
Texasguy is offline  
 
Reply With Quote Quick reply to this message
Old 07-08-2006, 09:11 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

You have to turn the corner at 90 degrees, then you can miter the face to get your 10 degree vault angle. so you will have side piece down the wall, a transitional piece, then your vault piece. The transitional piece will be cut to a point on the top. Experiment with short pieces first. Get an idea of what to do before you nail anything.

_/ /
/\/

(Pitiful drawing) You will have to raise the side wall crown to match the end wall crown.



__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 07-09-2006, 03:12 PM  
Texasguy
Junior Member
 
Join Date: Jun 2006
Posts: 5
Default

Thanks, Square Eye!
I read this over and kind of understood what you meant, then someone else I know suggested this site: http://www.garymkatz.com/TrimTechniq...dral-crown.htm
which basically says the same thing you did, only with pictures.
Now I need to figure out how to an outside corner wighout using a pendant.

__________________
Texasguy is offline  
 
Reply With Quote Quick reply to this message
Old 07-09-2006, 03:26 PM  
Square Eye
Senior Member
 
Square Eye's Avatar
 
Join Date: Jan 2006
Posts: 1,273
Liked 4 Times on 4 Posts

Default

Got that on my bookmarks and forgot all about it. Gary's site is very useful.

Someday, I may have TxBuilder to host a site like that for me to play on!

I just can't figure out a way to do the outside corner either. Pendants aren't bad, they just break up an otherwise smooth job when you only have one or two.

__________________

[URL="http://www.houserepairtalk.com/announcement.php?f=39&a=6"][size=3]The Ten Commandments of House Repair Talk[/size][/URL]



[URL="http://home.bellsouth.net/p/s/community.dll?ep=16&groupid=289528&ck="]Square Eye's home page[/URL]

Square Eye is offline  
 
Reply With Quote Quick reply to this message
Old 07-09-2006, 09:04 PM  
glennjanie
Senior Member
 
Join Date: Mar 2006
Posts: 2,990
Liked 2 Times on 2 Posts

Send a message via AIM to glennjanie
Default

Hi TexasGuy:
You can use 2 short pieces for a trial run. Lay one piece up on one side and mark lightly along the top of it, lay up the other piece and mark along the top of it. X marks the spot for the top cut on each one. Now for the bottom of the cut; Lay up one piece against the ceiling and the other up against it as if you were going to nail it, make a tick mark on the outer edge of the upper piece, repeat that with the pieces reversed. Now connect the top mark to the bottom mark and make your cut. If the short pieces work, the regular pieces should be a whiz.
Glenn



__________________
glennjanie is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Newest Threads

LATEST SPONSOR DEALS