Replacing Bathroom Exhaust Fan

Discussion in 'Walls and Ceilings' started by 1simple, Aug 19, 2009.

  1. Aug 19, 2009 #1

    1simple

    1simple

    1simple

    Member

    Joined:
    Feb 25, 2008
    Messages:
    11
    Likes Received:
    0
    I have considered replacing the exhaust fan in my bathrooms to something a lot quieter. The house has sheetrock. I could do it one of two ways, from the roof or cut a bigger hole in the sheetrock and then replace the hole with a new piece of sheetrock. This would be more work, but what I’m concerned about is the insulation in the attic. It is the blown in stuff, a 1 yr old house and if I go walking up there, I will be stepping on it, pushing it down, making it less effective….

    Any advice?

    Curtis
     
  2. Aug 19, 2009 #2

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,755
    Likes Received:
    249
    Just don't step on it. Move your foot around like your feeling for the rafters then step down. Kinda like walking down stairs when you can't see your next step. When you exit the attic, smooth it back out so you don't leave a void. You'll be wearing some of it when you come out so don't walk around the house, have a shop vac waiting for you real close by. Cellulose isn't too bad but, firberglass is a nightmare.
     
  3. Aug 19, 2009 #3

    1simple

    1simple

    1simple

    Member

    Joined:
    Feb 25, 2008
    Messages:
    11
    Likes Received:
    0
    Good idea, thanks!!
     
  4. Aug 19, 2009 #4

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,755
    Likes Received:
    249
    Glad to help, good luck.
     
  5. Aug 20, 2009 #5

    Nestor_Kelebay

    Nestor_Kelebay

    Nestor_Kelebay

    Emperor Penguin

    Joined:
    Mar 29, 2009
    Messages:
    1,844
    Likes Received:
    2
    I would say that if you're going to be replacing the bathroom fan, you're going to be going to and from that location a good few times before you're done. If it wuz me, I'd use a short piece of 2X4 to clear a path to the fan, and then put 2 foot wide by 4 foot long plywood handipanels down (if your attic access allows it) or some 8 foot long spruce 1X6's over the ceiling joists to provide a "walk way" to the fan. You'll have to overlap the boards or handipanels so that both ends are always on a joist.

    When you're finished, just remove the "walkway" as you make your way out, using a leaf rake or something to put the insulation back in place as you make your way out.

    If you're starting to do this kind of work on your house, you may as well "invest" in a good system as you may be wanting to install pot lights or check out possible roof leaks in future. So, it makes some sense to have some plywood and boards up in your attic to allow you to move about up there without putting a foot through a ceiling.

    I own a small apartment block where there simply isn't access to the bathroom fans from above. You have to do the entire job from below. It's do-able, but it's SOOO much easier to do this job when you have access from above.

    Also, one of the problems you're likely to run into is removing old duct tape. I use a heat gun to warm up the duct tape to soften the glue holding it to the galvanized duct. When it's hot it comes off easily. You could try a hair dryer, but the installers that work out of any retail flooring store will all have heat guns, and if you ask to borrow one for a day or two, and provide a $50 damage deposit or something, the Installation Manager at that place could probably provide one. Typically inexpensive heat guns come with a Hi-Lo-Off switch, whereas the expensive ones have a variable electronic temperature control. There's bound to be a cheap Hi-Lo-Off type heat gun kicking around the place that they don't use much, and that's all you need.
     
    Last edited: Aug 20, 2009

Share This Page