What should fixed plaster look like?

Discussion in 'Walls and Ceilings' started by randompete, Apr 13, 2010.

  1. Apr 13, 2010 #1

    randompete

    randompete

    randompete

    New Member

    Joined:
    Apr 13, 2010
    Messages:
    3
    Likes Received:
    0
    Hey all. I had a professional fix a 2x3 hole in my ceiling. The ceiling is plaster with an uneven finish similar to a popcorn, but very sporadic texture. It looked very much like a patch before we painted the ceiling, but I figured I'd see what it looked like afterward. It still looks very much like a patched hole. Not terribly ugly, but you can see it very clearly when you look at the ceiling. Is this normal? IS there any way to have the ceiling just look like one surface, short of tearing it down and drywalling the whole thing?
     
  2. Apr 13, 2010 #2

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,755
    Likes Received:
    249
    Done properly, it should appear seamless. You might want to bring it to the persons attention and see if he can fix it or call someone else who is confident that they can deliver results.
     
  3. Apr 13, 2010 #3

    randompete

    randompete

    randompete

    New Member

    Joined:
    Apr 13, 2010
    Messages:
    3
    Likes Received:
    0
    That's what I thought. I'll see if they can fix it tomorrow. What a bummer.
     
  4. Apr 13, 2010 #4

    Nestor_Kelebay

    Nestor_Kelebay

    Nestor_Kelebay

    Emperor Penguin

    Joined:
    Mar 29, 2009
    Messages:
    1,844
    Likes Received:
    2
    Randompete:

    Most likely the problem is not with the plaster repair itself, but with matching the existing texture. Plaster hasn't been commonly used for residential walls and ceilings since the late 1950's and early 1960's. So, that means that whomever textured your ceiling is probably dead and gone by now. Back then, they didn't have texture guns like they do now that simply throw joint compound on the wall or ceiling; they would use various favourite techniques to texture walls and ceilings by hand.

    What you'd be best off doing is taking a few pictures of your ceiling texture down to the places listed under "Drywall & Plaster" in your yellow pages. Ask if the texture on your ceiling was commonly used in your area, how it was done, and which of the remaining plastering contractors in your area might still do texturing like that.

    There are as many ways to texture a surface as there are plastering contractors, and the biggest problem with any repair to a textured wall or ceiling is usually matching the texture. Most of the time textures are created by smearing or spreading plaster or joint compound on the wall or ceiling in a particular way, but how thin or thick the plaster or joint compound is when it's applied will also affect the end result as well.

    If you can see that the ceiling isn't flush with the surrounding ceiling where the repair was done, that's one thing. If you can see cracks around the perimeter of the repaired hole, that's also poor workmanship. However, if the problem is that the texture doesn't match, you really can't blame the contractor too much for that. There are just so many different ways to make texture and so many different variables affecting it's appearance, that it's always difficult to match hand made textures well.
     
    Last edited: Apr 13, 2010
  5. Apr 14, 2010 #5

    randompete

    randompete

    randompete

    New Member

    Joined:
    Apr 13, 2010
    Messages:
    3
    Likes Received:
    0
    Thanks, Nestor. Good information. From where I stand, most of the problem is indeed in the texture. It is fairly obviously different from the rest of the ceiling. Unfortunately, there was no mention that this would be a difficulty when they took the job. I do also think that the surfaces are not equal depth. Just barely, but enough to exaggerate the texture differences. I'll see what they can do.

    Much obliged, gents.
     

Share This Page