DIY Home Improvement, Remodeling & Repair Forum > Search Forums > Search Results




Showing results 1 to 12 of 12
Search took 0.01 seconds.
Search: Posts Made By: Bubba Ray
DIY Home Repair Forum: Electrical and Wiring 01-23-2012, 05:50 PM
Replies: 13
Views: 1,662
Posted By Bubba Ray
alaska, good ideas. I have not heard from Miller...

alaska, good ideas. I have not heard from Miller after two emails. The power numbers come from Millers specs. Why the strange plug I have no idea but it may come from the fact that this welder can...
DIY Home Repair Forum: Electrical and Wiring 01-20-2012, 10:27 PM
Replies: 13
Views: 1,662
Posted By Bubba Ray
No way I am going to void the 3 year warranty on...

No way I am going to void the 3 year warranty on a new welder by changing the plug called for by the maker.
DIY Home Repair Forum: Electrical and Wiring 01-19-2012, 07:08 PM
Replies: 13
Views: 1,662
Posted By Bubba Ray
The plug is called for by Miller but the mig uses...

The plug is called for by Miller but the mig uses less than 30 amps.
DIY Home Repair Forum: Electrical and Wiring 01-18-2012, 04:07 PM
Replies: 13
Views: 1,662
Posted By Bubba Ray
Wire from box to outlet is 10 gauge. I have...

Wire from box to outlet is 10 gauge. I have received dif ideas on the white wire vs the ground wire to the third prong. Will not change end from welder as it is new with warranty.
DIY Home Repair Forum: Electrical and Wiring 01-01-2012, 02:10 AM
Replies: 13
Views: 1,662
Posted By Bubba Ray
Will check wires at panel Sunday.

Will check wires at panel Sunday.
DIY Home Repair Forum: Electrical and Wiring 12-31-2011, 06:08 AM
Replies: 13
Views: 1,662
Posted By Bubba Ray
New welder outlet wiring

My shop was wired years ago for 220 but no outlet was installed. I have black, red, white and green wires in box. The outlet called for by Miller is NEMA type 6-50 that has 3 connections with 1...
DIY Home Repair Forum: Insulation and Radiant Barriers 01-04-2011, 02:01 AM
Replies: 4
Views: 7,785
Posted By Bubba Ray
What is your location?

What is your location?
DIY Home Repair Forum: Insulation and Radiant Barriers 12-22-2010, 08:32 PM
Replies: 3
Views: 2,478
Posted By Bubba Ray
Not going to remove old stuff.

No way will I remove the old stuff. Will install baffles for sofit vents and have ridge vent now. Just planning to blow cellulose on top of the fiberglass. The access to this area is terrible!
DIY Home Repair Forum: Insulation and Radiant Barriers 12-13-2010, 04:00 PM
Replies: 3
Views: 2,478
Posted By Bubba Ray
OK to blow cellulose over blown fiberglass?

My access to 1/2 of my attic is thru a 1' by 2' hatch in a second story closet. The blown fiberglass is full of mice holes and acorns and is thin(2-4"). The freeloaders have been evicted. The area is...
DIY Home Repair Forum: Insulation and Radiant Barriers 12-13-2010, 03:19 PM
Replies: 2
Views: 1,267
Posted By Bubba Ray
I would be careful about insulating the floor...

I would be careful about insulating the floor with fiberglass in N.O. In SC it tends to hold moisture and provides living area for mice.
DIY Home Repair Forum: Plumbing Forum 03-29-2010, 07:25 PM
Replies: 9
Views: 1,240
Posted By Bubba Ray
I have done lots of copper but have used pex for...

I have done lots of copper but have used pex for a small repair and was impressed. Used the sharkbite fitting between the polybutalene and the pex with good results.
DIY Home Repair Forum: Plumbing Forum 03-29-2010, 07:21 PM
Replies: 3
Views: 1,060
Posted By Bubba Ray
We had a solid base installed in a upstairs...

We had a solid base installed in a upstairs shower that weighed a good 150lbs. It does not flex!
Showing results 1 to 12 of 12