Search results

The old wire could possible be stapled down. I doubt that it would be in the walls if it was put in more recently than the contruction process. It may be tacked along joists or something before it enters the walls. So I'd at least take a look for those before you start trying to pull it...

I say, about damn time! :D That still means 78% potential missed, but at least it's a step in the proper direction :( Engadget.com - SunPower announces 22 percent efficient solar panels or Full Article @ Yahoo

If the paint is coming off, the paper drywall covering may be coming off. If so, I would suggest trying to scrape off any of the loose, fuzzy fibers without damaging the drywall. Possibly sandpaper. Lay down a nice skim coat of drywall mud (top coat), whether only the spots that need it...

A hair dryer (or other non-flamable heat source) might soften it up enough. I am sure there are other options floating around.. but none are coming to me at the moment.

Thanks Kerrylib & bethany14. I would love to do radiant heating, but I am keeping my fingers crossed to remodel in the next year or 2.. doubling the square footage , and re-locating the kitchen. If it works out the way I would like, the entire addition will be on a concrete slab w/ radiant...

Thank you Kerrylib, that is exactly what I was trying to find. :D

I had stumbled across a product, or article about a product for refinishing your counter a ways back. I believe it was either a stone base (Sileston) or plastic (Corian) product. Tit was not thick like real granite, was only about ½” or less that was to be placed on top of existing...

Well, another project I’m considering forcing myself into, is to build the cabinets in my kitchen. I really really hate the thought of using particle board pre-builts, or assemble yourself cabinets at the big box stores. The only “affordable” ones aren’t all that affordable either. And...

No lighting? You mean no hard-wired lighinng right? The undercabinet lighting I will be using is corded, much like a lamp, but it mounts under the cabinet (or wall I imagine). An yes, my the range is gas, but still has electronic controls. It's really nice and I got a great deal on it :D

While the attached image is not to scale, it should give you a decent idea of what I’m looking at. The existing vent (Wall A) Is also for the Living room. The table, will mostly be against Wall B as generally there are only 3 of us. The cabinets on Wall A are typical wall...

Yes, there is more involved here I guess.. just trying to keep it simple. The entire houe was wired up on 4 or 5 14 gauge 2-wire circuits (no ground). I am in the process of running additional outlets in the kitchen using remodel boxes, and trying to keep the holes in the wall sot a...

Thanks for those bethany14... I think I'll call my wife and have her pick up some of that while she's out. This house had not been cleaned in a long time, the grease build up was something else. Nothing I tried seemed to work, til I used some oven cleaner (nasty stuff). I have used TSP...

Well, that is one of my concerns keeping it near/under the table. I can just picture the heat collecting under there, and us sitting at the table getting uncomfortable because underneath the table would be much warmer than the rest of the room. :confused:

It was pretty darn cold in my kitchen last year. My kitchen has one small heating duct., 4x9 as a guess. On that wall I plan on hanging some 12" wall cabinets, low-near base cabinet level. Originally I thought of putting a baseboard heater in, but I am concerned about the heat A) Damaging the...

1st Eelectrical group in kitchen. Well, here goes I think. below is a diagram for wiring up some outlets, primarily on a center wall in my house. #'s 2 and 4 are facing on the outside wall (Living room). #'s 5 & 6 primarily appliances (toaster, coffe pot, can opener, blender). #3 is...

Hello folks. So this time I want to install a dishwasher. Of course I have googled, but all I seem to find is a typical replacement proceedure. I want to isntall this dishwasher away from the sink. Running electrical w/ GFI I can do. Branching off the plumbing in the basement should be...

Unless you can get that same formica/laminate... I don;t think it would be a worthwhile cause. Even if you could find the same pattern, the age difference might be pretty obvious when compared side to saide due ot different dyes used then and now (as an example) as well as possible UV...

Hello all, just thought I’d drop by and let you know I am still alive. :) Its been what, a couple week or so since I made a post? Sorry, you all know life gets busy at times. Half of me says it feels like longer than two weeks, half feels like it was just a couple days ago, the third half...

The deed is done! So far I havent noticed any issues ( sitll have no washer/dryer). I shoudl have the appliances in a ocuple days. HEre is, as promised, pictures of the work. Also is the base frame I made for the w/d to sit on. It still has to be sheathed in ply, but strong enough for my bro...

Square Eye! Nice to hear form you. I wish it were that simple… to break into that first section of ABS and put the wye there, and run my hose right there, without any additional modification (well , maybe a little.. can't have water flowing out of the top of the wye when the sump...