Search results

Fridge Not cooling enough. Went from 30s to 60s. Repair guy said it might be Temp control board. We replaced it and did NOT solve cooling issues. Any suggestions would be appreciated! No one around here knows how to work on these refrigerators. Authorize service center over 3 hours away. Fridge...

Whirlpool Microwave got F2 code. Any suggestions where to start? The unit is 10 years old. Model MH1150XMS-2 Thanks!

My new Samsung refrigerator says to turn off the water before replacing filter. Just curious what other folks are doing. It’s a pain to pull the refrigerator out. I did not have to do this with my old Whirlpool. Thanks!! Stan Dupp

Looking for Hot Water Heater Recommendations. I currently have an electric 10 year old builder grade 50 gallon tank. The tank is located in a garage closet. I live in SC and the temperature in the garage is not regulated. Anyone have experience with the Heat Pump (Hybrid) hot water heaters...

I need to gain access and replace the front left burner on my stove. KESA907PSS02 Can you folks tell me how to remove the cook top. It appears to be different from the typical stoves. I can't find a video that looks similar to this stove. Thanks! Stan

Intermittent problem just got worse. When pressing the pad for ice to dispense, it works intermittently. I removed the ice container and made sure it's not binding. Any suggestions? Could the dispensing motor be going bad? Whirlpool Side by Side Fridge GS6NBEXRL00 The fridge is around 9 years

Came home from vacation and my washer panel is blank and can not start cycle. Checked power to outlet OK. I'm thinking maybe door switch? Any help would be appreciated! Whirlpool Calypso Washer 9 years old Model GVW9959KQ2

Hi folks I have a Whirlpool Calypso washer and matching Dryer. I need to replace the door switch on the Dryer. I am trying to figure out how to remove the top so I can access the switch. I have looked at some videos but they all look different then my dryer. Thanks for your help! Whirlpool...

I have a Kohler single handle, single whole kitchen faucet with pull out sprayer. Lately it’s gotten very stiff when turning the base side to side. What typically causes this and what should I try first to fix the problem? :confused: TIA Stan Dupp

I am thinking about replacing my heat pump AC unit. The air handler portion is in the garage attic, easily accessible. The current unit is a 3 ton 10 seer 7 year old Tappan. I think it’s slightly under sized; my house is 1,650 square feet with ten foot ceilings throughout most of the house. I...

I am not much of a plumber but I have installed a few faucets in my day. I would like to install a Metlund S-50 Series Hot Water Recirculation Pump in my master bedroom. I hesitate to attempt this job because the connections under my sink are PEX tubing and the values are FlowTite values (Push...

My yard has a lot of mole crickets, someone suggested I try Advion Mole Cricket Bait and at about $83 dollars for a 25 lb. bag it’s expensive. So I did try it and I still seeing a bunch of the little mounds they make. I’m not sure how well it’s working. Does anyone have any less expensive...

I have an area that I would like to install a low voltage recessed 2” puck light. I have a switched outlet about five feet from that area. My question is can I wire a plug to the transformer? Also does the transformer need to be put in some kind of box? TIA :confused:

I recently installed a GFCI receptacle outside. I used an inside bedroom outlet for the power source. My question is should I have installed the GFCI outlet inside the bedroom and a normal outlet outside? Would this be more cost effective since GFCI coast around $13 bucks? After I completed the...

When the builder built my house the back of the toilet was right up against the wall. They replaced the back of the toilet with a skinny one and that solved the problem. It appears the rough in was off, I measured and its 11”. Now I want to replace the old toilet with a chair height one. Should...

When the builder built my house the back of the toilet was right up against the wall. They replaced the back of the toilet with a skinny one and that solved the problem. It appears the rough in was off, I measured and its 11”. Now I want to replace the old toilet with a chair height one. Should...