Search results

Well this pos is trying my patience & sanity. I finally got the agitator to hold firmly & the next load of clothes I start hearing a whistling/scratching type noise so I go check and inside the agitator was full of water. Idk how or why but I'm assuming water started finding its way down to the...

Fixed it kind of. I removed the softener dispenser & the bolt holding the agitator to the gearcase shaft was way loose. I tightened the hell out of it & it worked & then came loose again about a minute later:mad:I cranked it down again & so far so good but I'm worried it'll come loose again. I'm...

Sns, looks like you were right. I put the new gearcase in & it still isn't agitating. I can hear it working but when I pry on the lid I see that it's not moving at all what so ever. I'm not lifting it up high at all that it would cause it to stop either. I called sears service & gave the lady an...

I got it. I took a long pry bar & used it with a hammer to whack the top of the gearcase shaft till it separated from the basket. But the basket and the nut are still stuck together. Got to wait for some time later this week to install the new one & test everything out.

Yes I removed the agitator & inspected the dogs. They're fine & I was able to remove the tub nut(used an exhaust clamp to get it off)the tub is still stuck & won't come out. I sprayed it down with some penetrating oil & am going to give it another shot in the morning. Hope it helps.

Well I'm back at it. After months of using a cheap used unit I bought I finally am getting around to replacing the gearcase on my busted whirlpool. I found a YouTube video on the procedure which is actually not to hard but after removing the tub nut (1:45 on video) the inner tub still won't come...

Thanks guys. I tried to retighten everything but it kept leaking so I said screw it & went to Home Depot & picked up a new faucet which included a new drain pipe I also bought new supply lines. Problem solved. Also yes everyone of the leaks seemed to only occur when the faucet was in use...

Hey folks. I got a few leaks coming from my restroom sink hopefully you can help me out a bit with. There's one coming from each of the water inlet hoses where they mate with the faucet, another from the pull thing to fill the sink with water and one from the drain valve where it connects with...

Ok I found the serial #wtw4800xq4. Anyhow I had a family friend I had forgotten about take a look at it, even though he works on these things as a side job he admitted he don't know much about these new style pulley type washers. After that & having to go to the laundromat for the past month I...

Where are the model #'s on these things? Also I ran the diagnostic mode thing on it & I have 3 blinking lights, not sure what to make of them or where to reference them. The 3 blinking are Sensing, rinse, done Followed by done and then repeated.

I'm thinking it is something else. The lid locks & when I pry on it I can see the agitator moving but barely, almost not at all. I can hear it to but it sounds very slightly different than when it was working

Thanks Neal. It's a whirlpool, #w10280544D.

Meant to say agitate not spin. It won't agitate.

Hello people:) I have a bit of a problem with my washing machine not wanting to spin. It is a whirlpool and barely going on 3 years old next February. It makes somewhat a similar sound to when it is working but weaker and when I pry the lid I can see that the agitator is not...

Thank you, much appreciated.

Perhaps but does that look like s part of the flange? Or maybe sewer pipe?

So my toilet flange is busted and I tried to remove it but I was only able to remove an outer diameter piece that had the slots for the closet bolts. I'm left with a hard to remove, plastic type piece that won't budge. I do not know if this is part of the sewer pipe or a stubborn piece of...