I bought self-tapping screws specifically for connecting steel studs to each other but the head of the screw sticks out too far, so where the studs attach to the top and bottom plate the screw head sticks out too much and it seems like it will affect how the drywall sits on the framing, meaning it won't sit flat.
Steel studs and attaching drywall
- Thread starter vinny186
- Start date
Help Support House Repair Talk:
Mastercarpenty
Junior Member
- Joined
- Aug 23, 2016
- Messages
- 235
- Reaction score
- 111
It usually half-dents and half-floats over the panhead screws. It's not a problem. Be sure you're using fine-thread screws for the drywall attachment as they hold better in metal.
Phil
Phil
There are basically 2 types of screws used fir the assembly of steel stud walls, pan head black phosphate and truss head.
Both are available in "A" point and tech.
The pan head black phosphate are often referred to as "framers" and are the prevalent screw used and the "tech" version, are the self drilling.
The truss head are plated and have a flatter head profile.
Both are available in "A" point and tech.
The pan head black phosphate are often referred to as "framers" and are the prevalent screw used and the "tech" version, are the self drilling.
The truss head are plated and have a flatter head profile.
If you're going to be doing a lot of drywall work in steel studs you're going to want a drywall screw gun. Cordless drills don't spin fast enough to get the self-tapping screws started. They'll eventually cut in and drive but it takes forever. I was doing a lot of steel stud work at my kids' private elementary school. When I first started I was using a cordless drill, after awhile I broke down and bought a corded driver. Once you get the hang of it and get it dialed in right it makes the process much faster.
nealtw
Contractor retired
You use fine thread drywall screws for steel studs.
They are actually coarse thread;http://www.grabbercanada.ca/CatBrow...=+L2P3MIyRNPZk0xBscqzuiavQru1HOGaJUoC8ss13/8=
I've used screws specifically for steel studs, I've used coarse and I've used fine. Doesn't matter which one I use the drywall screw gun is much faster than a cordless drill. I made do for a long time, but the drywall gun is a much better tool for the job if you're going to do a lot of drywall on steel studs. It still gets a good work out when I do volunteer work hanging sheetrock. Once I'm dialed in I can drive 3 screws in the time it takes someone using a cordless drill to drive one. If I had one of those fancy ones that used drywall screws that are collated and fed automatically I could really fly. Can't justify that expense as a DIYer though.
Last edited:
The distinction between coarse and fine thread comes from the gauge of the steel being worked with, where tin can or 25ga studs you experience less "spinout" with "A" point coarse thread, 20ga and lower are most often assembled with fine thread, tech screws.
Mastercarpenty
Junior Member
- Joined
- Aug 23, 2016
- Messages
- 235
- Reaction score
- 111
Most of the residential and DIY metal studding is the light-gauge stuff. Pointed screws hold better here because they expand the metal around them tightly as they go in instead of having metal removed by drilling. The fine-thread ones are recommended for metal because they have much more surface of the thread engaging the metal than coarse-threaded ones do. Coarse works better for wood because there's less tendency to tear out the wood fibers and strip or pull out. Drill points are needed for heavy-gauge studs because the pointed screws can't penetrate that much steel and they often break just as they go in from binding since the heavier steel doesn't expand around them.
I've got a stud crimper and indeed it's faster, but in more and more areas it's use is being prohibited. The problem isn't the crimped connection but over-zealous drywall installers who push so hard on the screw-gun that the connection comes apart. Since this is usually seen only inside the wall (invisible) it requires skill and care to avoid the issue and codes try to be idiot-proof in their required methods. Look for them to become universally outlawed soon.
Phil
I've got a stud crimper and indeed it's faster, but in more and more areas it's use is being prohibited. The problem isn't the crimped connection but over-zealous drywall installers who push so hard on the screw-gun that the connection comes apart. Since this is usually seen only inside the wall (invisible) it requires skill and care to avoid the issue and codes try to be idiot-proof in their required methods. Look for them to become universally outlawed soon.
Phil
Thanks for all the suggestions.
The screws I used to assemble the studs did not hinder the hanging of the drywall - like someone said, the screws get indented into the drywall. I also used coarse fine screws to attach the drywall and I had to put my cordless on it's "2" setting, it definitely took longer than wood and a drywall bit was necessary because you're pushing so hard while drilling that the screw will often go thru the paper but I only had one wall so wasn't too much of a hassle.
The screws I used to assemble the studs did not hinder the hanging of the drywall - like someone said, the screws get indented into the drywall. I also used coarse fine screws to attach the drywall and I had to put my cordless on it's "2" setting, it definitely took longer than wood and a drywall bit was necessary because you're pushing so hard while drilling that the screw will often go thru the paper but I only had one wall so wasn't too much of a hassle.
