DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Gutter Diversion Quick FIx




Reply
 
Thread Tools Search this Thread Display Modes
Old 12-30-2010, 11:48 PM  
Deke7619
Junior Member
registry_dropdown_21077_52620
 
Join Date: Dec 2010
Location: Skaneateles, ny
Posts: 5
Default Gutter Diversion Quick FIx

Hi....I just purchased a place with known problems that I will be fixing over time. The foundation is a problem due to drainage, partly because there is inadequate gutters and poor overall drainage. I am attaching pictures of one of the gutters that drains directly to the foundation. Anyone have a simple (temporary) solution to diverting the water from this gutter away from the house? I don't know how to best mount a temporary downspout below this inadequate gutter and divert the runoff through PVC. Any thoughts would be appreciated.


gutter1.jpg   GUTTER2.jpg  
Deke7619 is offline  
 
Reply With Quote
Old 12-31-2010, 12:40 AM  
nealtw
Contractor
registry_dropdown_20526_52623
 
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 12,851
Liked 1267 Times on 1117 Posts
Likes Given: 2123

Default

it looks like the metal flashing is sticking out a few inches You should be able to cut a hole and install the plastic gutter drain in that area and have a sheet metal shop make a plug for the end. take pictures and measurements with you


nealtw is offline  
 
Reply With Quote
Old 12-31-2010, 07:09 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
registry_dropdown_4883_52627
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,311
Liked 144 Times on 122 Posts
Likes Given: 71

Default

Maybe buy a piece of pvc gutter and notch the side of it to catch the water and divert it away from the foundation. This will definitely be an eye sore until you can figure a better method.
kok328 is offline  
 
Reply With Quote
Old 12-31-2010, 11:48 AM  
Deke7619
Junior Member
registry_dropdown_21077_52639
 
Join Date: Dec 2010
Location: Skaneateles, ny
Posts: 5
Default

Thanks for the input. Here's a bad and not to scale photoshopped idea of what might work. Could I notch out some corrugated PVC pipe, attach it to the gutter, and just run that down and away from the house? It seems like it would work as long as I can get it fastened securely. Any thoughts? Thanks.
GUTTER 3 copy.jpg  
Deke7619 is offline  
 
Reply With Quote
Old 12-31-2010, 12:04 PM  
oldognewtrick
Moderator
HRT_ADMIN.png
 
oldognewtrick's Avatar
registry_dropdown_15773_52640
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 6,782
Liked 651 Times on 534 Posts
Likes Given: 205

Default

Deke, well thats on way to do it, but I'd suggest getting a 12" piece of 6" gutter and some gutter brackets with the screw in fasteners, 2 end caps, 1 outlet, a tube of gutter caulk, 1-10' 3X4" down pipe, 2 "A" elbows, 1 "B" elbow and 20' of black corrugated plastic drain pipe that is not slotted but solid. For less than $25.00 you can fix the problem permanently.
oldognewtrick is offline  
 
Reply With Quote
Old 12-31-2010, 12:45 PM  
Deke7619
Junior Member
registry_dropdown_21077_52641
 
Join Date: Dec 2010
Location: Skaneateles, ny
Posts: 5
Default

Quote:
Originally Posted by oldog/newtrick View Post
Deke, well thats on way to do it, but I'd suggest getting a 12" piece of 6" gutter and some gutter brackets with the screw in fasteners, 2 end caps, 1 outlet, a tube of gutter caulk, 1-10' 3X4" down pipe, 2 "A" elbows, 1 "B" elbow and 20' of black corrugated plastic drain pipe that is not slotted but solid. For less than $25.00 you can fix the problem permanently.
OK Old Dog...I think I'm with you.... Are you saying that the the existing gutter is standard square 6" gutter, and that I can attach to that? I haven't measured it, but it doesn't look standard to me. I'll have to measure. Assuming that's true and I can join a new piece to it, I think you're saying to add a 12" section plus an outlet, cap it, and run a rigid downspout and divert with solid corrugated drain pipe. Sounds good. What's the second end cap for? Thanks.
Deke7619 is offline  
 
Reply With Quote
Old 12-31-2010, 01:00 PM  
oldognewtrick
Moderator
HRT_ADMIN.png
 
oldognewtrick's Avatar
registry_dropdown_15773_52646
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 6,782
Liked 651 Times on 534 Posts
Likes Given: 205

Default

What I'd suggest is putting the small section of new gutter below the existing, secured to the fascia board, trim back the metal of the existing so it has plenty of room to drain into the new gutter but not close enough to drip behind it. Place the end caps on the section of gutter, crimp the edge and caulk. Cut the hole for the outlet, insert the outlet, pop rivet the outlet, caulk around the edge of the outlet then start hanging the down pipe. Use the 2 "A" elbows at the top, one opposite the other, you may need a small piece of down pipe between them to stretch to the wall, secure the down pipe and put the "B" elbow at the bottom.
oldognewtrick is offline  
 
Reply With Quote
Old 12-31-2010, 01:14 PM  
Deke7619
Junior Member
registry_dropdown_21077_52647
 
Join Date: Dec 2010
Location: Skaneateles, ny
Posts: 5
Default

Quote:
Originally Posted by oldog/newtrick View Post
What I'd suggest is putting the small section of new gutter below the existing, secured to the fascia board, trim back the metal of the existing so it has plenty of room to drain into the new gutter but not close enough to drip behind it. Place the end caps on the section of gutter, crimp the edge and caulk. Cut the hole for the outlet, insert the outlet, pop rivet the outlet, caulk around the edge of the outlet then start hanging the down pipe. Use the 2 "A" elbows at the top, one opposite the other, you may need a small piece of down pipe between them to stretch to the wall, secure the down pipe and put the "B" elbow at the bottom.
Great idea! Thanks!


Deke7619 is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Is it a foreclosure or quick-sand? AlwaysOneMoreProject Introductions 4 10-29-2010 08:56 AM
quick question hoarea Electrical and Wiring 17 02-21-2008 05:05 AM
Quick Survey Travers Carpentry and Woodworking 0 12-18-2006 03:40 PM
the quick and the dead jcambece General Chit-Chat 0 05-31-2006 11:33 AM

Newest Threads

LATEST SPONSOR DEALS