DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Carpentry and Woodworking > Replacing trim, ceiling no level




Reply
 
Thread Tools Search this Thread Display Modes
Old 04-09-2011, 04:40 PM  
chotown
Junior Member
registry_dropdown_22144_55798
 
Join Date: Apr 2011
Location: Chelmsford, MA
Posts: 5
Default Replacing trim, ceiling no level

I removed some ceiling beams and as part of the process needed to remove some trim. I cut a board to size and put it up to test the fit. Fit is great except there is a gap as something is not quite level I'm guessing the ceiling.

I attached a pic. How can I make the board flush through the entire span. It is 13' stretch.

I'm not concerned with where the trim meets the ceiling as I wil put some crown molding there but I want the trim to be flush with the board that it meets at a 90 degree angle. You can see in the picture that in the middle there is a gap.


cam1.jpg   P1030340.JPG   P1030337.JPG  
chotown is offline  
 
Reply With Quote
Old 04-09-2011, 06:17 PM  
inspectorD
Housebroken
HRT_ADMIN.png
 
inspectorD's Avatar
registry_dropdown_391_55800
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,243
Liked 180 Times on 151 Posts
Likes Given: 450

Default well

To be on the safe side,this to me looks like there is a sag in the ceiling. Is this a bearing wall that someone did not make the beam large enough? I do not know, but if I where you I would look into it.

As for the trim if it's good to go, just install the crown , You will never notice it when it is finished, actually happens alot in older homes, just split the difference best you can and call it done.


__________________
Just My
Made in the
inspectorD is offline  
 
Reply With Quote
Old 04-09-2011, 07:36 PM  
chotown
Junior Member
registry_dropdown_22144_55806
 
Join Date: Apr 2011
Location: Chelmsford, MA
Posts: 5
Default

The beams I took down were decorative and the one in question is load bearing. Having just bought the house I can't say about the beam being sized ok. Hopefully it is just a case of an old house. The house is 47 its old.
chotown is offline  
 
Reply With Quote
Old 04-10-2011, 05:02 AM  
joecaption
Senior Member
registry_dropdown_21184_55808
 
Join Date: Jan 2011
Location: Hartfield VA, VA
Posts: 1,501
Liked 83 Times on 68 Posts
Likes Given: 2

Default

Sure looks like someone removed part of a supporting wall to me.
I'd bet the floors up stairs are sagging and bouncy also. There is a way to fix this right so it will no longer sag, the floors up stairs will be flatter, doors up stairs will not be croooked.
joecaption is online now  
 
Reply With Quote
Old 04-10-2011, 06:31 AM  
chotown
Junior Member
registry_dropdown_22144_55809
 
Join Date: Apr 2011
Location: Chelmsford, MA
Posts: 5
Default Best course of action

Do I need an engineer and contractor or will a goI'd contractor know how to fix this.
chotown is offline  
 
Reply With Quote
Old 04-10-2011, 07:10 AM  
chotown
Junior Member
registry_dropdown_22144_55810
 
Join Date: Apr 2011
Location: Chelmsford, MA
Posts: 5
Default

Meant to type good contractor.
chotown is offline  
 
Reply With Quote
Old 04-10-2011, 06:16 PM  
inspectorD
Housebroken
HRT_ADMIN.png
 
inspectorD's Avatar
registry_dropdown_391_55818
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,243
Liked 180 Times on 151 Posts
Likes Given: 450

Default well

A good contractor will be fine. You can have them engineer what they need at a local lumber yard.
An engineer will give you what you need also, either way your going to end up paying something.
This actually happens alot....when folks do not pull permits, and DIY. You just happen to be on the receiving end, but it is an easy fix with a new beam and temporary walls, or even a steel plate bolted to the sides. Depends on the structure.
Good luck.
__________________
Just My
Made in the
inspectorD is offline  
 
Reply With Quote
Old 04-11-2011, 07:18 AM  
chotown
Junior Member
registry_dropdown_22144_55832
 
Join Date: Apr 2011
Location: Chelmsford, MA
Posts: 5
Default Thanks

I appreciate the advice. would rather get it squared away. And you are absolutely right about the floors upstairs. I was wondering why they sagged in a certain area and now I see it corresponds with where that beam is below.
chotown is offline  
 
Reply With Quote
Old 04-11-2011, 05:01 PM  
inspectorD
Housebroken
HRT_ADMIN.png
 
inspectorD's Avatar
registry_dropdown_391_55848
 
Join Date: Dec 2005
Location: Litchfield, CT
Posts: 4,243
Liked 180 Times on 151 Posts
Likes Given: 450

Default Great

Keep us in the loop, so others can learn from what you are going through.

Good luck!!


__________________
Just My
Made in the
inspectorD is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
replacing stapled ceiling with dry wall nopilot Walls and Ceilings 4 12-01-2010 03:21 PM
Framing basement partition - ceiling not level gqskrub Framing and Foundation 3 11-04-2010 05:48 PM
Replacing popcorn ceiling chibe_k Walls and Ceilings 3 10-20-2009 08:02 AM
Replacing a Ceiling Fan w/ Reg. Fixture crapbathroom Electrical and Wiring 2 09-08-2009 05:40 PM
Replacing outside door trim eddie Carpentry and Woodworking 4 08-13-2007 06:33 PM

Newest Threads

LATEST SPONSOR DEALS