DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Framing and Foundation > replace load bearing wall with beam

Help Support House Repair Talk by donating using the link above.
Thread Tools Search this Thread
Old 01-10-2012, 01:59 PM  
Join Date: Dec 2011
Posts: 30
Default replace load bearing wall with beam

We just bought an old two story house (1959). There is a load bearing wall inside of the room on the first floor. On top of this room are second floor bedrooms, bathroom and a porch. The headers of this load bearing wall (the orange part in the attachment house3.jpg) are damaged by termite. The wall carries the weight of the second floor, a wall and siding on second floor and ceiling of the second floor (attic floor).
We are trying to replace the wall with new header beam. I have talked to different contractors and got somehow inconsistent answers. I would appreciate any help and input here.
The current header beam consists of two 2x10 and there are double 2x4 top plates on top the header beam. One segment of the current header has span of 10' and the rest header span are 3' to 5' with post of two or three 2x4s. We would like to have as few posts in the room.
The questions are:
1) If we use double Georgia-Pacific 1 3/4"x9 1/2" LVL as header, what's the biggest span we can have? Is two of these LVL enough? One contractor suggests we put three LVL side by side.
2) Do we still need top plates when the new header is one long piece? Do we need bolt and glue the LVL together? How much stronger is one 3 1/2" thick beam vs two 1 3/4" together?
3) What type of post should we use? We have been suggested to use 4x4, 6x6 and we are thinking to use 3" steel column.
4) Any special treatment of the ground needed for the post? Right now the wall is on the edge of the house foundation. Contractors say they would just put the post directly on the concrete. But I found out the ground is only a layer of 1/2" thick concrete on top of (unfilled) cinder block. I am thinking either put a large steel plate on the ground and then put the post on top to distribute the weight, or dig a few small holes and try to fill the cinder block with liquid cement. I would like to avoid digging big 3'x3' post hole in the middle of room, also there might be a sew pipe under.

Click image for larger version

Name:	house3.jpg
Views:	2780
Size:	38.9 KB
ID:	3453   Click image for larger version

Name:	IMG_9597.jpg
Views:	5074
Size:	48.0 KB
ID:	3454   Click image for larger version

Name:	IMG_9603.jpg
Views:	3397
Size:	62.3 KB
ID:	3455   Click image for larger version

Name:	IMG_9605.jpg
Views:	4904
Size:	65.0 KB
ID:	3456   Click image for larger version

Name:	wall.gif
Views:	2491
Size:	19.9 KB
ID:	3457  

Last edited by minimii; 01-10-2012 at 04:20 PM.
minimii is offline  
Reply With Quote
Old 01-10-2012, 05:03 PM  
Contractor retired
nealtw's Avatar
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 23,595
Liked 2999 Times on 2628 Posts
Likes Given: 4939


The top plates are not important and can be changed out when you install the beam.
We also call those cut studs cripples but you may as well know they are jack studs.
You will get a mixed bag of suggestions here just like your contractors. An engineer is the guy that should decide the size of the beam, the length that the foundation will support on posts, dictating distance between posts and how big they should be. Once you have that plan in place now you can get quotes from your contractors, all quoting the same job.

nealtw is offline  
Reply With Quote
Old 01-11-2012, 03:16 AM  
Senior Member
BridgeMan's Avatar
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 744
Liked 79 Times on 69 Posts


You would do best by consulting with the manufacturer of the load-bearing products you intend to use. Both Georgia-Pacific and TrusJoist (Weyerhaeuser) have engineering staff to assist in determining what size and type of products would work best for your situation. Or hire a local engineer to crunch some numbers for you after doing a site visit, and possibly come up with a design for a built-up beam that you could fabricate on site. Going that route would be a lot less expensive for the materials (when I last checked for prices on TrusJoist Parallams for a remodel, a 30-foot, 5-1/4" x 14" was going for $795, and that was 11 years ago). Your local engineer could also make some column and column support recommendations to best serve your needs.
BridgeMan is offline  
Reply With Quote
Old 01-11-2012, 04:30 PM  
Join Date: Jan 2012
Posts: 54

Anything can be's all just a matter of cost. An engineer will be able to tell you what's need to do the research into costs with contractors. As Neal said, use the engineer to get the facts...not a contractor that will frame it up and say "That ought to hold it"

Also figure if you want a flush or boxed-down beam...changes the labor ALOT.
__________________ Beware of the "do-it-all contractor".
Jdmrenovations is offline  
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
is this a load bearing wall? justdoitalready Framing and Foundation 5 07-19-2016 08:33 AM
Load-bearing beam replacement..with out the walls above coming down RatRodPontiac Framing and Foundation 6 12-23-2011 09:12 AM
Shear Wall load bearing central wall w plaster removal? Tomoca Framing and Foundation 2 11-29-2010 05:43 PM
Load Bearing Wall Removal Advice (point load?) stringer9 Framing and Foundation 8 10-25-2010 02:48 PM
Load bearing wall bfash General Home Improvement Discussion 9 11-28-2007 09:01 AM

Newest Threads