DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > Roof and wall sheathing




Reply
 
Thread Tools Search this Thread Display Modes
Old 07-05-2012, 11:03 AM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,855
Liked 1404 Times on 1238 Posts
Likes Given: 2425

Default

It looked like the math could end up with a 97" stud on the high wall which would have to come from a 10 ft board , that's all. Yes I think you math is fine.


nealtw is offline  
 
Reply With Quote
Old 07-05-2012, 04:39 PM  
vikasintl
Member
Join Date: Apr 2011
Location: lakewood, wa
Posts: 40
Likes Given: 2

Default

Well, I already have 8 feet 2x4s so I would use them so it would be 96" instead 97" which is ok if its one inch lower...its fine...I have to adjust one and half inch for double top plate any way......I have to cut only the lower walls from 8 feet boards...
Thanks for all your help...I don't think I have any more questions as of now..


vikasintl is offline  
 
Reply With Quote
Old 07-06-2012, 02:10 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,855
Liked 1404 Times on 1238 Posts
Likes Given: 2425

Default

You should cut all the stud with angle on top, same angle as the pitch of the roof.
Square to long on the high wall and square to short on the low wall. Keep the top plate short on both walls so the side wall top plates overlap and tie everything together.
nealtw is offline  
 
Reply With Quote
Old 07-07-2012, 02:19 AM  
vikasintl
Member
Join Date: Apr 2011
Location: lakewood, wa
Posts: 40
Likes Given: 2

Default

Ok thanks a lot..
vikasintl is offline  
 
Reply With Quote
Old 07-19-2012, 01:21 PM  
vikasintl
Member
Join Date: Apr 2011
Location: lakewood, wa
Posts: 40
Likes Given: 2

Default

Ok one more question...the lower wall should also have two top plates and one bottom plate ..total 3 plates?
vikasintl is offline  
 
Reply With Quote
Old 07-19-2012, 02:26 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,855
Liked 1404 Times on 1238 Posts
Likes Given: 2425

Default

Yes the top plate is held back so the top plate of the side walls can overlap. That locks the corners together.
I just went looking for a picture to show what I was talking about. I guess I've been over building sheds. No wonder most look so crappy after a few years.
I did find this write up.
http://www.constructioncalc.com/blog...shing-returns/


nealtw is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
2 queations about siding job -- Fiberboard Sheathing & CertaWrap golem Roofing and Siding 0 08-20-2011 08:28 AM
Hole in sheathing under vinyl siding at outside outlet edlank Roofing and Siding 8 08-17-2011 01:03 PM
Rip 4'x8'x 3/4' plywood roof sheathing to 2'x8' for easier install? WallyPop Roofing and Siding 3 07-25-2009 06:21 PM
Why was fiberboard used as sheathing in the 70's? SeattleDIY General Home Improvement Discussion 1 11-25-2008 06:16 AM
Repair of damaged external sheathing Shark Flooring 0 08-04-2007 03:14 PM

Newest Threads

LATEST SPONSOR DEALS