DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Oatey's Great White Joint Compound or Harvey's Wet Set PVC Cement for Wet PVC




Reply
 
Thread Tools Search this Thread Display Modes
Old 08-12-2012, 09:20 PM  
billhead1
Member
 
Join Date: Apr 2012
Location: Baton Rouge, Louisiana
Posts: 32
Liked 1 Times on 1 Posts
Likes Given: 4

Default Oatey's Great White Joint Compound or Harvey's Wet Set PVC Cement for Wet PVC

I replaced my plugged AC condensate P-trap with a P-trap that has an internally threaded cleanout plug at the bottom of the trap. Unfortunately, this P-trap has a very small drip in the vicinity of the cleanout plug that does not appear to be due to condensate build-up on the outside of the P-trap. The AC evaporator/condensor is located in my attic, so any leakage will damage the ceiling below. Since the P-trap has been in service about 24 hours, it is filled with condensate and will have to be drained through the cleanout connection, but the P-trap fitting can not be removed for servicing because it is glued into the AC condensate drainage system.

In researching the best remedy for stopping the leak, I came across Oatey's Great White Joint Compound with PTFE (White Paste) or Harvey's Wet Set PVC Cement. According to the instructions, the Wet Set PVC cement can be applied to wet fittings, but obviously the cleanout plug will no longer be removable for servicing if this option is pursued.

The Joint Compound instructions state that it is flexible, non-hardening, and withstands up to 10,000 psi on fittings, so the cleanout plug can be removed for servicing in the event of future P-trap pluggage; however, there is no mention of whether it can be applied to a wet PVC fitting.

Does anyone know if the joint compound would work acceptably on a wet schedule 40 PVC fitting?

One thought would be to apply the joint compound to the interior threads of the P-trap cleanout, and then, if the cleanout fitting still has a minor leak, to seal the outside of the cleanout fitting with Wet Set PVC cement. The P-trap is not under any external pressure - just gravity flow of AC condensate from about 12 inches above, which is less than 1/2 psi of pressure.

Any suggestions would be greatly appreciated.



__________________

Last edited by billhead1; 08-12-2012 at 09:25 PM.
billhead1 is offline  
 
Reply With Quote Quick reply to this message
Old 08-13-2012, 08:12 AM  
kok328
Supporting Member
HRT_SUPPORTER.png
 
Join Date: Nov 2007
Location: Grand Blanc, MI
Posts: 2,230
Liked 116 Times on 101 Posts
Likes Given: 65

Default

Have you considered teflon tape for the threaded connections?

__________________
kok328 is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
using joint compound for decorative effect jjm Decorating and Design 13 08-29-2012 07:39 PM
All purpose joint compound tractng General Home Improvement Discussion 1 08-24-2011 02:27 PM
Cement Compound. Foundatio Bricks, Masonry and Concrete 10 03-10-2010 03:36 PM
Hello from the Great White North! :) Carlitosway Introductions 1 01-25-2010 02:44 AM
Joint compound in a box? Leal Flooring 4 06-29-2008 12:32 AM

Newest Threads

LATEST SPONSOR DEALS