DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Walls and Ceilings > tongue and groove pine on ceiling




Reply
 
Thread Tools Search this Thread Display Modes
Old 04-18-2013, 07:41 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

They have some strange building practices. Besides that, the black stain on the sheeting looks like mold and should be tested. The blocks in the soffet vent area should not be there, unless you just have them there while it's open. The 8x8 hole was a roof vent, I hope they replaced it with a ridge vent, which you should be able to see from below thwe center. If you really want to fix the hole in the sheeting, Cut a 2x6 to the length of the distance between the trusses and nail a 7x7 peice of sheeting to it, slide it into place and nail thru the trusses to hold it in place. The lack of vapour barrier is just as bad as the ice dam for causing the mold in the attic and yes you need fire rated drywall.
While you have it open throw in another stud on each side of the door and then at door knob height put a block between those studs and the next studs, that will keep the strangers out when your not home.


nealtw is offline  
 
Reply With Quote
Old 04-19-2013, 12:53 AM  
Fredartic
Junior Member
Join Date: Apr 2013
Posts: 15
Liked 1 Times on 1 Posts

Default

http://www.photocal.fr/features_-_ph..._photocal.html

That product pretends to control mold and mildew. I don't know for that product but in the house, I had pulverised all the area, the attic, the walls, the floor with a specific product used with a machine for that that I had rented at Home depot. Here's the link: http://www.homedepot.com/p/Concrobiu...4#.UXDpgbWQVmM

Should I test the area? If it is recommanded to do that, what is the process? Can I do it by myself?


Fredartic is offline  
 
Reply With Quote
Old 04-19-2013, 05:36 AM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

HD has a home test kit. It sure wouldn't hurt to know it was good before closing it up.
nealtw is offline  
 
Reply With Quote
Old 04-19-2013, 10:44 AM  
Fredartic
Junior Member
Join Date: Apr 2013
Posts: 15
Liked 1 Times on 1 Posts

Default

Thanks, it will be a reason for another trip to HD. I will test it and be back with the result in few days.
Fredartic is offline  
nealtw Likes This 
Reply With Quote
Old 04-19-2013, 11:57 PM  
Fredartic
Junior Member
Join Date: Apr 2013
Posts: 15
Liked 1 Times on 1 Posts

Default

If I use Roxul product insulation,

http://www.roxul.com/products/reside...ul+comfortbatt

that is fire resistant, do I need gyproc?
Fredartic is offline  
 
Reply With Quote
Old 04-20-2013, 04:46 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

Where I live you do?
nealtw is offline  
 
Reply With Quote
Old 07-02-2013, 06:32 PM  
Fredartic
Junior Member
Join Date: Apr 2013
Posts: 15
Liked 1 Times on 1 Posts

Default

Quote:
Originally Posted by nealtw View Post
To be on the safe side you could drywall first and then cover it with pine. If the rafter are a 24" on center, 5/8 drywall would be required.
It's 16" on center, so is the drywall would be 5/8 or thinner?
Fredartic is offline  
 
Reply With Quote
Old 07-02-2013, 06:38 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

I think TX drywall is 5/8 and it is rated for 1 hour of fire stop.
nealtw is offline  
 
Reply With Quote
Old 08-10-2013, 11:58 AM  
Jungle
Senior Member
Join Date: May 2013
Posts: 339
Liked 29 Times on 26 Posts
Likes Given: 31

Default

That looks bad with the black mold. It's funny how they say osb board is suppose to be mold resistant. It always seem to have the mold in a house. Have you been having allergy problems?
There is no fixing that, it needs to be taken out. Or sell it, but you could be sued!
As for the pine wood, i would mention a couple of things, 1) it can be heavy so your structure might not support it. I would chose a veneer. 2) Some people can have wood allergies too, something to think about before you wood your whole house.
Jungle is offline  
 
Reply With Quote
Old 08-11-2013, 12:21 PM  
Fredartic
Junior Member
Join Date: Apr 2013
Posts: 15
Liked 1 Times on 1 Posts

Default

Quote:
Originally Posted by Jungle View Post
That looks bad with the black mold. It's funny how they say osb board is suppose to be mold resistant. It always seem to have the mold in a house. Have you been having allergy problems?
There is no fixing that, it needs to be taken out. Or sell it, but you could be sued!
As for the pine wood, i would mention a couple of things, 1) it can be heavy so your structure might not support it. I would chose a veneer. 2) Some people can have wood allergies too, something to think about before you wood your whole house.
As I said before, I used a product with the machine for that purpose that is suppose to treat the mold. There is no odor in the house. It seems that the product did the job. Of course there is still the black color on the OSB, but no more mold. So, why replacing it? As I understantd, it could be a problem if it wasn't treated but it's not the case.

For the t and g pine, I want to use a very thin product, just 5/16, so it isn't heavy, not much than the gypse. Actually, the gypse isn't 5/8, I think it is 3/8, so I imagine I can use 5/16 pine...


Fredartic is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Need help with tongue and groove m2244 Carpentry and Woodworking 8 02-23-2013 10:16 PM
Can you get thin tongue and groove? m2244 General Home Improvement Discussion 1 02-19-2013 01:51 PM
Disign advice. Cottage look, planks, v-groove m2244 Walls and Ceilings 2 01-15-2012 09:01 AM
Tongue and grove floor buckling up pstew96 Flooring 18 11-15-2011 08:37 AM
Painting Pine cibula11 Decorating and Design 4 08-14-2008 09:46 AM

Newest Threads

LATEST SPONSOR DEALS