DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Repairing Chip in Tub




Reply
 
Thread Tools Search this Thread Display Modes
Old 12-28-2013, 03:57 PM  
trogdor
burninator
Join Date: Dec 2013
Posts: 29
Liked 2 Times on 2 Posts
Likes Given: 2

Default Repairing Chip in Tub

We have an old 1955 tub that is metal with a white finish. I don't know much about tubs but it looks ceramic to me. There is a nickel-sized chip in the finish that is slowly growing larger. I went to Home Depot and found a two-part epoxy product, but the reviews were terrible, with most people saying the product never fully adhered or came right up several weeks later. Others complained of the product turning yellow and looking terrible.

This is not a major eyesore, so if we just have to leave it there, we will. I'm not willing to spend more than $40 or two hours of time on this project. If it can be done inside those parameters, great. If not, that's ok too.

Any advice would be appreciated.


trogdor is offline  
 
Reply With Quote
Old 12-28-2013, 04:45 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

Welcome to the site. You have baked on enamal finish, the steel will rust thru if not repaired The two part epoxy is likely your best bet. It may take a few trys to get it right, it will never dissapear


nealtw is offline  
 
Reply With Quote
Old 12-29-2013, 11:57 AM  
trogdor
burninator
Join Date: Dec 2013
Posts: 29
Liked 2 Times on 2 Posts
Likes Given: 2

Default

Thank you for replying. Are you saying the product is a good one and people who have poor results with it are using it incorrectly?
trogdor is offline  
 
Reply With Quote
Old 12-29-2013, 12:18 PM  
oldognewtrick
Moderator
HRT_ADMIN.png
 
oldognewtrick's Avatar
Join Date: Jul 2009
Location: Nashville, TN
Posts: 7,099
Liked 696 Times on 569 Posts
Likes Given: 221

Default

Prep is critical to any adhered product performing. How it holds up in your tub can only be a matter of time and usage. When time and funds allow, look into getting it refinished by a pro. In the meantime give the 2 part a try and don't skimp on prepping.
oldognewtrick is offline  
 
Reply With Quote
Old 12-30-2013, 12:14 AM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,522
Liked 1354 Times on 1195 Posts
Likes Given: 2329

Default

Yes I would just repeat Oldogs post. Your bathroom is well past overdue for an upgrade and you just want to make it last another ten years.
nealtw is offline  
 
Reply With Quote
Old 12-30-2013, 08:51 PM  
trogdor
burninator
Join Date: Dec 2013
Posts: 29
Liked 2 Times on 2 Posts
Likes Given: 2

Default

Thank you. I will be diligent with the prep work. As to the suggestion that the bathroom needs to be remodeled or tub professionally refinished because of a nickel-sized chip in the enamel, I'll pass. Logic like that is the very reason our national leaders have led us into trillions of dollars of debt.

I appreciate the responses. After I use the product from HD, I will stop back by to update with my results.


trogdor is offline  
nealtw Likes This 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Repair chip in new tub Colette Plumbing Forum 9 03-16-2013 08:46 AM
Rusted chip in tub JenPN Plumbing Forum 4 06-25-2011 02:18 PM
Bath Tub Chip newtda Plumbing Forum 6 12-03-2008 06:07 AM
Granite Counter Chip Repair SpenceFish Introductions 2 01-02-2008 06:28 AM
Repairing Acrylic Snoop General Home Improvement Discussion 1 03-17-2006 06:17 PM

Newest Threads

LATEST SPONSOR DEALS