DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Plumbing Forum > Use of 90 degree sweep verses 45+45




Reply
 
Thread Tools Search this Thread Display Modes
Old 01-20-2014, 01:39 AM  
SuperD
Junior Member
Join Date: Jan 2014
Posts: 3
Liked 1 Times on 1 Posts

Default Use of 90 degree sweep verses 45+45

New to this forum and could not find my answer under a search.
1.) What are the rules ( DWV, ABS for Canada) when using 90 degree sweeps instead of two 45 degree elbows? My senerio is 3 inch main drain stack to a new second story 3 piece bathroom and I have 3 of the 90 degree turns I need to make. I see that plumbers often use a 90 degree sweep at the toilet closet , but after that they seem to stick with always using two 45 degree fitting to minimize the restriction.
2.) Can I use a 90 degree sweep at the horizontal to vertical transition?
3.)Is there any where else (besides venting) that I can use a 90 degree sweep?
4.) And what is the best way to know I have purchased a long sweep?
Thanks Greatly!


SuperD is offline  
 
Reply With Quote
Old 01-20-2014, 10:47 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,845
Liked 1403 Times on 1237 Posts
Likes Given: 2423

Default

Welcome to the site. Calgary puts out this booklet. http://www.calgary.ca/pda/dba/docume...f?noredirect=1


nealtw is offline  
 
Reply With Quote
Old 01-21-2014, 09:28 AM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
Join Date: Feb 2010
Location: San Diego
Posts: 1,506
Liked 513 Times on 392 Posts
Likes Given: 209

Default

I prefer the single 90 degree sweep when possible. Toilets must have them by code in USA. The fewer the fittings (and turns), the easier the water flow. If water is speeding up as it turns the corner (usually going from horizontal to vertical), use a short sweep. If water is slowing down (usually from vertical to horizontal), use a long sweep.
CallMeVilla is offline  
 
Reply With Quote
Old 01-21-2014, 06:28 PM  
SuperD
Junior Member
Join Date: Jan 2014
Posts: 3
Liked 1 Times on 1 Posts

Default

Thanks for the input. Perhaps I will check with a local plumber and then buy him lunch.
SuperD is offline  
nealtw Likes This 
Reply With Quote
Old 01-21-2014, 06:32 PM  
nealtw
Contractor
Join Date: Nov 2010
Location: Upper Fraser Valley, British Columbia
Posts: 13,845
Liked 1403 Times on 1237 Posts
Likes Given: 2423

Default

Quote:
Originally Posted by SuperD View Post
Thanks for the input. Perhaps I will check with a local plumber and then buy him lunch.
Villa and I like lunch
nealtw is offline  
 
Reply With Quote
Old 01-21-2014, 08:08 PM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
Join Date: Feb 2010
Location: San Diego
Posts: 1,506
Liked 513 Times on 392 Posts
Likes Given: 209

Default

And beer ...
CallMeVilla is offline  
 
Reply With Quote
Old 01-21-2014, 08:42 PM  
SuperD
Junior Member
Join Date: Jan 2014
Posts: 3
Liked 1 Times on 1 Posts

Default

As soon as you mention lunch or beer they come out of the woodwork!
SuperD is offline  
 
Reply With Quote
Old 08-02-2014, 02:37 AM  
jamesdalton
Banned
Join Date: Aug 2014
Posts: 1
Default

Quote:
Originally Posted by SuperD View Post
As soon as you mention lunch or beer they come out of the woodwork!
Hehe.... Cheers
jamesdalton is offline  
 
Reply With Quote
Old 08-02-2014, 09:58 AM  
Wuzzat?
Banned
Join Date: Jan 2010
Posts: 2,328
Liked 168 Times on 155 Posts
Likes Given: 94

Default

http://www.google.com/search?client=...UTF-8&oe=UTF-8

Using
http://www.co.lincoln.or.us/planning...mbingguide.pdf
and others from
http://www.google.com/search?client=...UTF-8&oe=UTF-8
you might be able to reverse-engineer the basic rules driving these choices of fittings.

The answer might be in here
http://www.engineeringtoolbox.com/pv...ngs-d_801.html
I just added "engineering toolbox" to the previous search.
This has two 45s being less or more resistant than a long sweep 90, depending on the pipe diameter. Whoda' thunk it???

Last edited by Wuzzat?; 08-02-2014 at 10:14 AM.
Wuzzat? is offline  
CallMeVilla Likes This 
Reply With Quote
Old 09-06-2014, 04:23 AM  
WyrTwister
Member
Join Date: May 2014
Posts: 40
Liked 7 Times on 6 Posts

Default

If you ever have to run a snake in the drain pipe , the less abrupt bends / transitions , the better your chances are .

I ended up using two 45 degree fittings to make an offset , on my 2" PVC kitchen drain line .

God bless
Wyr


WyrTwister is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Best way to cut 45 degree end joints jmc0319 Carpentry and Woodworking 34 08-12-2014 01:04 PM
sewer slope and sweep Dionysia Plumbing Forum 0 10-13-2011 07:09 PM
Magna Sweep Self Cleaning System HauteShots Pools and Spas 2 04-20-2011 06:15 AM
Thermostat degree settings house92 HVAC 4 10-11-2009 05:21 PM
Replacement Door Sweep touchton Windows and Doors 1 11-14-2007 07:18 PM

Newest Threads

LATEST SPONSOR DEALS