DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Home Improvement Discussion > Determining a load bearing wall




Reply
 
Thread Tools Search this Thread Display Modes
Old 01-08-2008, 07:31 AM  
Daryl in Nanoose
Senior Member
 
Daryl in Nanoose's Avatar
registry_dropdown_546_14022
 
Join Date: Feb 2006
Location: Nanoose Bay, BC
Posts: 764
Liked 4 Times on 4 Posts
Likes Given: 5

Default

Thats what this forum is all about "helping people" and that asking about something is the best way to go. Gladd we could help


__________________
[url]http://edhome.shawwebspace.ca/[/url]
Daryl in Nanoose is offline  
 
Reply With Quote
Old 11-11-2013, 06:01 AM  
jet1952
Junior Member
registry_dropdown_32289_93237
 
Join Date: Nov 2013
Posts: 1
Default

I had a car port and I closed it in. I took down the outside wall and left a small portion that was a exterior door way. I decided removed the wall (sheet rock ) from existing door way . There is a frame wood for the door way , there are two 2x4,posts back to back from floor to ceiling then an additional 2x4 that is part of the door frame.The original wall ran north to south the rafters in my attic run east to west. The peak of my roof is directly under the under the spot wherethe pole is located. Sorry I am a woman trying to do repairs and this is the best I know how to explain . Is this a load bearing support. Or can I remove it.


jet1952 is offline  
 
Reply With Quote
Old 11-11-2013, 07:29 AM  
CallMeVilla
Contractor
 
CallMeVilla's Avatar
registry_dropdown_17830_93240
 
Join Date: Feb 2010
Location: San Diego
Posts: 1,472
Liked 489 Times on 377 Posts
Likes Given: 202

Default

Hey Jet ... you are asking a smart question. It would really help if you could post some pictures but your "word picture" is very helpful.

If that wall framing is open for you to see, that "post" probbaly goes from the floor to the peak of the roof. It IS a supporting member. That does not mean it cannot be resupported in a different manner. However, just removing it outright is NOT the thing to do without more input from professionals in this forum.

Patience.

Send pics and we can help you in the process. OK? In the meantime, here is a graphic that explains the terms for framing. It will help you explain your situation better.
Wall.JPG  
CallMeVilla is offline  
nealtw Likes This 
Reply With Quote
Old 11-12-2013, 08:09 PM  
BridgeMan
Senior Member
 
BridgeMan's Avatar
registry_dropdown_23463_93305
 
Join Date: Aug 2011
Location: Cottage Grove, Oregon
Posts: 738
Liked 75 Times on 67 Posts

Default

Jet, there is no need to apologize for being a woman doing home repairs. We all had to start somewhere, learning how to do things without the place falling down around us. With some decent instructions on sites like this, a few good references, and perseverance, you'll eventually be able to do a typical job as good as, if not better than, most men.
BridgeMan is offline  
 
Reply With Quote
Old 11-16-2013, 04:26 PM  
Snoonyb
Member
registry_dropdown_2280_93424
 
Join Date: Sep 2006
Posts: 46
Liked 1 Times on 1 Posts

Default

If you have a basement with a center support beam and this wall occurs above above that beam, either parallel or perpendicular with the floor joists, it could be load bearing.

If your house is single story, in the attic, if the ceiling joists continue over it, end over it, are spliced over it, or you have roof bracing landing on it, It's a bearing wall. If the ceiling joist are parallel with the wall and you have roof bracing landing on it, It's a bearing wall.

If there is a 2nd floor above the wall, you have two options. You can remove a section of ceiling on both sides of the wall to determine if the 2nd floor, floor joists, cross it or end over it. If so, Its load bearing. Or you can use a stud finder to determine the location and direction of the joists.

Here is a link that should be of assistance;
http://www.awc.org/pdf/WCD1-300.pdf
__________________
Illigitimas non-carborundum
Snoonyb is offline  
nealtw Likes This 
Reply With Quote
Old 03-22-2014, 06:36 PM  
C51089
Junior Member
registry_dropdown_33302_102238
 
Join Date: Mar 2014
Posts: 1
Default

I have had 4 contractors, 2 said yes, 2 said no, if this is a load bearing wall!! Our living room, dining roomis a vaulted ceiling!!!
The wall I want down is between the dining room and the kitchen and hallway!!! They both have pass thrus!!! It's the cornersI want taken down so it will be a open counter!!!It is a one story dwelling!!!
Can I cut the corners???

Last edited by C51089; 03-22-2014 at 06:45 PM. Reason: Additional sentence.
C51089 is offline  
 
Reply With Quote
Old 03-22-2014, 06:50 PM  
oldognewtrick
Moderator
HRT_ADMIN.png
 
oldognewtrick's Avatar
registry_dropdown_15773_102239
 
Join Date: Jul 2009
Location: Nashville, TN
Posts: 6,938
Liked 669 Times on 548 Posts
Likes Given: 208

Default

Quote:
Originally Posted by C51089 View Post
I have had 4 contractors, 2 said yes, 2 said no, if this is a load bearing wall!! Our living room, dining roomis a vaulted ceiling!!!
The wall I want down is between the dining room and the kitchen and hallway!!! They both have pass thrus!!! It's the cornersI want taken down so it will be a open counter!!!
Really have to say I have no clue what you want to do. If you have a question, it's best to start a new thread and not piggy back on an existing thread, it gets confusing. Post pics and be a little more specific about your particle situation. And, if you are modifying structure, getting the opinion of contractors, in my opinion, is probably not your best course of action. Contact a structural engineer and get their opinion about what is and what is not load bearing.

Oh yeah, to House Repair Talk!
oldognewtrick is offline  
nealtw Likes This 
Reply With Quote
Old 03-22-2014, 06:58 PM  
Snoonyb
Member
registry_dropdown_2280_102240
 
Join Date: Sep 2006
Posts: 46
Liked 1 Times on 1 Posts

Default

Off hand I would say that it is bering, however. a single line drawing ID'ing the rooms and the slope of the vault would be helpful.


__________________
Illigitimas non-carborundum
Snoonyb is offline  
 
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Load Bearing Wall question cruickshanks Framing and Foundation 6 12-18-2008 08:10 AM
Load bearing wall (its not really a wall) icemaker Walls and Ceilings 3 03-28-2008 08:10 PM
Opening wall, don't think it's load bearing? CZSteve Walls and Ceilings 8 01-15-2008 12:45 AM
Load bearing wall bfash General Home Improvement Discussion 9 11-28-2007 08:01 AM
load bearing wall from 1920 Will Carpentry and Woodworking 7 07-18-2006 09:35 AM

Newest Threads

LATEST SPONSOR DEALS