DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > Roofing and Siding > Flat roof on block of flats - rebuild advice




Reply
 
Thread Tools Search this Thread Display Modes
Old 01-07-2009, 02:58 PM  
Martinr
Junior Member
 
Join Date: Jan 2009
Posts: 2
Default Flat roof on block of flats - rebuild advice

I live in a 1970s block of flats with a flat roof, which is now beyond patching and needs stripping and rebuilding.

I'd really appreciate a bit of independent advice regarding the rebuild, as roofers have a vested interest in putting forward their own proposals.

We've engaged a building surveyor and he has presented his proposals; however, a trusted roofer I discussed them with is not convinced.

The decking is woodwool without a cement screed. In addition, the existing roof has a miserable fall of one and a half inches in 11 feet. It really is a flat roof.

The surveyor proposes:

1. Strip existing felt off.

2. Fit tilting fillets and OSB to give improved falls to valleys feeding to existing rainwater pipes.

3. Fit polyurethane insulation slabs on a vapour barrier.

4. Lay a high performance torch-on felt underlay and mineral-faced cap sheet.

5. New edge detail because new roof surface would be 150mm higher than present.


The roofer has commented that putting OSB over the existing decking (with the tilting fillets in between) is not a good idea - it could induce sweating; however, with the thermal insulation on top of the OSB/vapour barrier, I'm not sure this is a valid comment as the decking and OSB would now be in a warm roof in theory.

I also need to be convinced that the OSB can be properly attached to the existing structure.

The roofer also does not like the mineral-faced capsheet because he says it's difficult to get a good edge joint. He prefers (if I've understood it correctly) to use a 4mm high-performance capsheet painted with solar reflective paint after laying.

I'd be most grateful for any thoughts and comments on the above.

Many thanks

Martin



__________________
Martinr is offline  
 
Reply With Quote Quick reply to this message
Old 01-10-2009, 04:48 AM  
Martinr
Junior Member
 
Join Date: Jan 2009
Posts: 2
Default

Quote:
Originally Posted by the roofing god View Post
SEEMS YOU HAVE A HAIR BETTER THAN 1/4" PER FOOT REQUIRED FOR MOST RUBBERIZED BITUMEN products,Certainteed Flintlastic S.A makes an excellent 3-part system with a granular cap sheet,They also have a torchdown model---we have no problems with lap edges on granulated,you should do a 45 degree lap cut,top & bottom selvages,then weld the lap-no problems
Yes, I'm in the UK and at the moment it's very frosty and cold. Meanwhile, I have the local agent of Icopal/Anderson roofing materials coming in the next couple of days. They offer a free service whereby they assess the roof and come up with a spec for its renewal, obviously centred around their own products. It'll be a good opportunity for me to get his comments on the proposals already obtained.

I also spoke to the technical people at Ruberoid and they too said that, certainly along the side joints, there should be no problem getting a good joint with mineral-faced capsheet, although they admitted that on cut edges care obviously is needed.

Thanks.

Martin


__________________
Martinr is offline  
 
Reply With Quote Quick reply to this message
Old 01-12-2009, 04:51 AM  
roofer
Roofing Expert
 
Join Date: Jan 2009
Posts: 6
Default

listen to theroofinggod,he`s got it right,funny that I only see his post in your blurb though,What`s up with that anyway ?

__________________
roofer is offline  
 
Reply With Quote Quick reply to this message
Old 01-16-2009, 10:26 AM  
handyguys
Senior Member
 
handyguys's Avatar
 
Join Date: Feb 2008
Location: USA
Posts: 815
Liked 2 Times on 2 Posts

Send a message via Skype™ to handyguys
Default

Yea, I have done torch downs like you describe with the paint on and the granular. The granular will have a seam that you could see but it will be water tight. No worries there. If you have enough pitch that you wont puddle then I wouldn't raise things up, its more work and not really necessary. Just have all old work completely removed and any deck repairs made. If you have no insulation in attic/under roof now is the time to consider adding it.

__________________

The Handyguys Podcast [url]http://www.handyguyspodcast.com[/url]

handyguys is offline  
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
Near flat roof leaking should I shingle over? Donny Roofing and Siding 16 01-06-2012 07:56 PM
Looking at buying a flat roof house mikeb33 Roofing and Siding 9 05-13-2009 10:37 AM
Flat Roof SPISurfer Roofing and Siding 5 11-20-2008 11:12 AM
Flat Roof geordieT Roofing and Siding 1 04-14-2008 10:02 AM
Flat roof leaking - repair? replace? rlarkin70 Roofing and Siding 4 06-07-2007 06:53 PM

Newest Threads

LATEST SPONSOR DEALS