DIY Home Improvement, Remodeling & Repair Forum > DIY Home Improvement > General Appliance Discussion > Maytag Model# LDE7600ACL loud clicking noise

Help Support House Repair Talk by donating using the link above.
Thread Tools Search this Thread
Old 08-26-2010, 02:32 PM  
Junior Member
Join Date: Aug 2010
Location: Tampa
Posts: 1
Default Maytag Model# LDE7600ACL loud clicking noise

I have a Maytag Model# LDE7600ACL dryer that runs and heats OK but started making a noise like a small jackhammer; rapid loud ratcheting noise. I took the front off and ran it and it *seems* to be more on the left-hand side.

Any tips appreciated.

ghh3rd is offline  
Reply With Quote
Old 08-26-2010, 11:52 PM  
Emperor Penguin
Nestor_Kelebay's Avatar
Join Date: Mar 2009
Location: Winnipeg, Manitoba
Posts: 1,844
Liked 2 Times on 2 Posts


Well, on a front loading Maytag dryer, the motor and blower wheel are both on the left side of the machine (when viewed from the front).

Depending on the speed of the clicking noise, it could be anything from a loose clothes lifter causing a noise with each rotation of the drum to the vanes on the blower wheel hitting against something causing about 20 clicks with each rotation of the motor.

On the back of those dryers you should find an inspection cover on the lower right side, opposite the lower left side of the dryer when viewed from the front. If you remove that inspection cover, you can observe the operation of the idler pulley to see if it's doing anything strange.

Typically, on a Maytag front loading dryer, the first thing to go are the rear drum rollers, and when they go, they make a chirping noise that fairly quickly becomes a loud squeeling noise if you don't replace those rear drum rollers. So, the fact that it's not the drum rollers means that it's either something peculiar (like something having fallen down past the lint filter and hitting against the blower wheel) or maybe a broken idler pulley, or maybe something inside the machine resting against the rotating drum and bouncing around as it hits the bolts that hold the clothes lifters in place.

At this point, your best bet would be exploratory surgery.

Maybe before you do that, go to some websites that are run by appliance repair techs and see if that noise you're describing is indicative of anything. For several of those web sites, go to the Refrigerators Forum and read a thread entitled "GE Refrigerator Problem" by EJ1948. (It's the 4th thread down in the list.)

If appliance repair techs can't identify that clicking as indicative of any one part going bad, then about the only thing you can do is take the front panel off, take the front bulkhead off, pull the dryer drum out (along with the drive belt) and run the machine without the drum inside it to locate the source of that clicking noise. (You will have to jumper the two wires that go to the door switch to get the machine to run without the front panel and bulkhead in place.) It's really that easy to take the drum out of a Maytag front loading dryer, but it takes a bit more patience to put it back in.

Also, if you go to any place that sells automotive tools, you should be able to buy a mechanic's stethoscope for under $20 (and often for less than $10). A mechanic's stethoscope has a metal probe on it that is attached to a large diaphragm. When that probe is touched against something that's making noise, it will cause the large diaphragm to move in the same way and make the same noise, so that the noise you hear through the ear phones will be considerably louder when the probe is in contact with the part making the noise. In this way, you can pinpoint the source of the noise.

A mechanic's stethoscope costing less than $20. The extension rod screws on to the end of the stethoscope for greater reach. Mechanic's stethoscopes can cost anywhere from $5 to $500 depending on quality, but even a cheap one will give good results. I've been fixing cars and major appliances for well over 20 years, and mine cost me about $10 when I bought it. Mechanic's stethoscopes are excellent for locating the source of a noise in any machinery, and well worth their cost, especially for the cheapest ones.

To use a mechanic's stethoscope you simply put it on your ears and touch the metal probe against any part you think might be making the noise you're hearing from the machine. The closer the probe is to the source of the noise, the louder the noise will be when heard through the mechanic's stethoscope.

Also, Maytag factory authorized service manuals for your model of dryer are not expensive, and can be ordered from Maytag Publications at 1-888-547-8279. Maytag has recently been purchased by Whirlpool, so Whirlpool might be running things differently now, but you still should be able to get Maytag factory authorized service manuals from Maytag or Whirlpool. They might even have the manual for your dryer available online for downloading at no cost.

Last edited by Nestor_Kelebay; 08-27-2010 at 12:23 AM.
Nestor_Kelebay is offline  
Reply With Quote
Old 08-27-2010, 12:13 PM  
Cork Flooring Pros
Cork-Guy's Avatar
Join Date: Oct 2009
Posts: 243

MAYTAG LDE7600ACL (07 - THERMOSTATS) | Bell Parts Appliance Model Lookup

That diagram might help you with your exploratory surgery

Note: The left hand side has diagrams for the rest of the dryer.
Cork Flooring - Ventless Fireplace
Cork-Guy is offline  
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Similar Threads
Thread Thread Starter DIY Home Repair Forum Replies Last Post
A/C fan runs, but I hear a clicking noise. rmoreaux1 HVAC 7 08-01-2011 08:09 AM
Old Furnce making clicking noise when starting JeremyB HVAC 1 03-01-2011 07:07 PM
Help 2 year old York AC leaking freon and making clicking noise(video, pics inside) tennisfan20 HVAC 3 10-01-2010 12:11 PM
loud pop in the wall missmeggie Walls and Ceilings 1 02-01-2010 10:54 AM
Sump Pump making LOUD noise - no water inside E2009 Plumbing Forum 3 08-12-2009 10:06 AM

Newest Threads