Search results

House Repair Talk

Help Support House Repair Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. W

    French doors vs sliding glass doors vs????

    These (total opening doors) are considerably more expensive than either French swinging (in or out swinging) (less expensive) or sliding doors (Least expensive). Weather resistance and crime resistance vary with manufacturer and locking system. When the glass is broken with any of the doors...
  2. W

    Best product for cleaning green algea-looking stuff off siding?

    Use that too works well, lasts 2-3 years
  3. W

    Exterior metal trim on vinyl replacement windows

    I have done lots of break metal, would not be acceptable to me.
  4. W

    PEX-b brass fitting failure

    I installed a Moen Flo valve a few years ago. Takes a month to set flow through fixtures but then shuts off the water immediately if it senses unusual flow or even minor drip. Cell phone operated, easily shut off if filling a swimming pool etc. sensors are available the can be placed at the...
  5. W

    Sealing casement windows

    Condensation is the most likely cause. Deep jambs and /or high moisture levels (50% plus relative humidity) will result in condensation in lower corners of windows. Best to lower interior humidity to less than 45% in winter time or allow more circulation near windows, heavy insulated drapes or...
  6. W

    Whole house/stand by generators

    I looked into whole house generator Generac in particular with transfer switch. (+/- $4000.00 ). My installation location was adjacent to exterior electric meter and gas meter. Suprised to see installation also in $4000.00 range. Absolute highway robbery. Have 7500 watt Generac portable...
  7. W

    water heater recommendation

    If you replace the anode every 5 years, the heater will last indefinitely. They cost +/- $100.00. It is a sacrificial metal rod that carodes rather than the heater wall itself.
  8. W

    Replacement windows and rotten sills

    I'm aware of that, with the price point this fellow is at did not seem this was a viable option. New PVC brickmold, etc. are also available, considerably more expensive than capping.
  9. W

    Replacement windows and rotten sills

    Nothing said here about a written contract, proof of insurance or workman's comp insurance. Any work included should be clearly stated in the contract as should any work not specifically included. Rotted sills must be replaced and then capped along with any jamb and head capping "prior to"...
  10. W

    How to clean and replace glass?

    Hate to be the bearer of bad tidings but any door manufactured after 1980 requires the utilization of safety glazing meeting Z97.1 and CPSC requirements. Current IBC code requires that you must bring entire door into compliance when replacing glass. Meaning all panes must be re-glazed with...
  11. W

    ventless gas insert

    Have had one for several years. No problems whatsoever. Have CO detector close by, (0) reading. previously had one that was manual, hot to adjust or turn off. Current has remote, have to replace 3 C cell batteries once a year, no issues. Chimney has been stuffed with fire resistant...
  12. W

    2016 andersen windows reduced thickness 2.2mm low e glass vs. 3.1mm.......

    I worked in the window business for over 40 years. ALL glass by ALL manufacturers changed to metric about 1980 because of international trade, not because they were trying to cheapen the product. The glass went from polished plate to float at approximately the same time. is probably the least...
  13. W

    How many folks use the energy saving bulbs?

    Changing any and all bulbs to LEDs including exterior spots. Purchase when on sale especially at Costco where they have 1/2 price sales often. Have several CFLs that I will gladly give away. Pure Junk
  14. W

    Crown molding

    Rocklear has a great jig +/- $15.00 that has proper positioning printed on it and sandpaper front and back so molding stays in place on jig and jig stays in place on saw.
Back
Top