Painting over water-damaged drywall

Discussion in 'Painting Forum' started by dave547, Nov 11, 2010.

Help Support House Repair Talk by donating using the link above.
  1. Nov 11, 2010 #1

    dave547

    dave547

    dave547

    New Member

    Joined:
    Nov 11, 2010
    Messages:
    1
    Likes Received:
    0
    Hi folks,

    In my bathroom, there is a retainer wall that enclosed the shower/bathtub. The caulking around the tub eroded over the years and water seeped through to the exposed retainer drywall. After recaulking the tub, I sanded down the wall, spackled where needed, and repainted, but it doesn't look any better. Since I am new to painting and repairing walls, I am wondering if perhaps I didn't sand or spackle enough, or if I even used the right materials.

    So my question is, how do I make this wall look nice and new? Any help would be appreciated!

    Thanks,
    Dave

    [​IMG]

    [​IMG]
     
    Last edited: Nov 11, 2010
  2. Nov 11, 2010 #2

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,797
    Likes Received:
    264
    If the drywall crumbled due to water damage, replacing the drywall is the only solution otherwise, you need to put more mud over the recessed areas and allow it to dry completely. Some shrinkage will occur so you may need several coats to bring the recessed areas up to a flush surface.
     
  3. Nov 17, 2010 #3

    HDwetPaint

    HDwetPaint

    HDwetPaint

    Member

    Joined:
    Nov 1, 2010
    Messages:
    15
    Likes Received:
    0
    Hey Dave,
    Luckily you don’t have a very large area to repair so it shouldn’t be very difficult. When repairing any water damaged areas it’s usually a pretty good idea to stay away from your normal spackling compound. Most lightweight or fast dry spackles are water soluble and what it looks like to me is the water from the paint broke it down causing it to shrink. In order to fix it the right way without replacing the section of drywall you will need; medium to fine grit sandpaper, plaster or drywall compound, a putty knife, a paint brush, and some oil/shellac based primer sealer.
    First you want to remove all the old water damaged paint if you haven’t already, this is very important because your repair job is only going to hang on as good as whets underneath it. You will just need to lightly scrape and sand the affected areas until you feel you have a good base for your repair and the new paint. Next you will want to dust the surrounding area off removing any loose chips and dust from the previous step and you are ready to prime. It is important you use either a shellac or alkyd(oil) based primer to prevent not only any residual moisture in the drywall from damaging your wall again but to prevent cracking, bubbling, or even stain bleed in the future. Once the primer is dried completely you are ready to patch or skim coat the damaged area. Going with a thicker wallboard compound is important not only that it sands very easily but it will provide a stronger repair. The plastering may take a few coats as it will shrink as it dries. Once it is completely dried you are going to need to sand it smooth, the area you’re working in will make sanding a pretty easy job. I prefer to use a sanding block when I do any skim coating because it helps level everything out at an even rate but it’s not 100% necessary. After you have a nice smooth surface dust off the wall and throw another coat of primer on it, sometimes once it is primed you may notice some small surface imperfections make sure to re-patch and prime them. If the wall looks and feels good at this point finish the job off with a topcoat of paint and you should now have a nice even repair that wont damage nearly as easy as the spackle. Got any more questions about how or why you need to do something let us help you out.
    Thanks, Jeff
     
  4. Jun 4, 2012 #4

    museumreplicas

    museumreplicas

    museumreplicas

    Member

    Joined:
    May 9, 2012
    Messages:
    15
    Likes Received:
    0
    It looks very odd, if the wall is ruined by water. Very first scrub all over the wall with hard brush. Then for the best result, apply plaster of parish all over the wall. Now it will be better to use plastic paint over it. It will minimize the degradation of wall due to water.
     
  5. Jun 5, 2012 #5

    joecaption

    joecaption

    joecaption

    Well-Known Member

    Joined:
    Jan 8, 2011
    Messages:
    2,146
    Likes Received:
    324
    Not sure why but the picture will not come up on my computer.
    Without that picture it's hard to do anything but guess.
    Is this drywall in the wet area? There should be no drywall exposted in a wet area.
    There is no "just patching" drywall that has got wet and is crumbling. It needs to come out and be replaced.
    The only place a spackle would be used is for small nail holes, not tape setting or skim coating.
    Plastic paint:eek:
    Plaster of Paris:eek:
     
  6. Jun 6, 2012 #6

    oldognewtrick

    oldognewtrick

    oldognewtrick

    Administrator Staff Member Admin Moderator

    Joined:
    Jul 26, 2009
    Messages:
    10,900
    Likes Received:
    1,482
    Joe the op is from 2010, just a old post brought back to life.
     

Share This Page