double switch

Discussion in 'Electrical and Wiring' started by hoarea, Apr 11, 2008.

Help Support House Repair Talk by donating using the link above.
  1. Apr 11, 2008 #1

    hoarea

    hoarea

    hoarea

    Member

    Joined:
    Jan 29, 2008
    Messages:
    11
    Likes Received:
    0
    can some one try to explaine this to me. i have a double switch i am trying to change it to two single ones problem is in side the box there are only three wires red, black, and white. red is on top left, black is on bottom left and white is on top right. red and black are not connected. the run two different lights and there is no other switchs for them. is it posible to put 2 switches in?
     
  2. Apr 11, 2008 #2

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,762
    Likes Received:
    250
    I'm not sure I understand your question.

    However, you can not replace a 3-way switch with two one way switches.
     
  3. Apr 11, 2008 #3

    hoarea

    hoarea

    hoarea

    Member

    Joined:
    Jan 29, 2008
    Messages:
    11
    Likes Received:
    0
    it is not a three way switch. a three way switch would have 2 switches for one light would it not?
     
  4. Apr 12, 2008 #4

    triple D

    triple D

    triple D

    Well-Known Member

    Joined:
    Jan 30, 2008
    Messages:
    296
    Likes Received:
    1
    Horea, I'm quite sure what you are describing is a 3-way switch. Check the switch, it should not say on/off on it. If it does, it will be a first for me. A three way will not have any writing on it. The only thing is where is the other end hiding? Sometimes in a remodel I will disable one end by nutting the black and white together and putting a blank on the box. This allows the other end to act as a single pole. See if you can't gather some more info for us, like how many wires are in the light fixture boxes. Maybe we can help you out with some of those old school tricks. Let us know, good luck....
     
  5. Apr 12, 2008 #5

    hoarea

    hoarea

    hoarea

    Member

    Joined:
    Jan 29, 2008
    Messages:
    11
    Likes Received:
    0
    ok. i no it is a double switch with two switch lever, a three way switch has only one switch lever.now one lever turns on a ceiling light in the back room and the other lever turns on a outside light. so this is why i am confused. there should be a forth wire.
     
  6. Apr 12, 2008 #6

    Square Eye

    Square Eye

    Square Eye

    Well-Known Member

    Joined:
    Jan 13, 2006
    Messages:
    1,273
    Likes Received:
    10
    Someone may have dropped a 3 wire into the box from the last fixture or from a junction box in the ceiling. The switch sounds like a duplex top/bottom switch.
    The power most likely comes in on the white and returns on the red and the black. GET A METER. Check it out. If you can't get a meter, turn the breaker off, connect the black and white. Turn the breaker back on and go look to see which light comes on. turn the breaker back off and connect the white and red, breaker back on, check again which light comes on. If nothing, turn the breaker back off, then try black to red. One of those wires will work with both lights and that will be your common power source. Pigtail it with 2 leads. Run one to each switch. Then the other 2 wires, one to each switch.
     
  7. Apr 13, 2008 #7

    hoarea

    hoarea

    hoarea

    Member

    Joined:
    Jan 29, 2008
    Messages:
    11
    Likes Received:
    0
    thanks for all the help. did what square eye said and it worked fine. white was hot
     
  8. Apr 14, 2008 #8

    Square Eye

    Square Eye

    Square Eye

    Well-Known Member

    Joined:
    Jan 13, 2006
    Messages:
    1,273
    Likes Received:
    10
    YAY!!!

    I got ONE right! :D
     

Share This Page