Refinishing Concrete Floor Sand/polish/stain/seal

Discussion in 'Bricks, Masonry and Concrete' started by harleysilo, Jan 6, 2014.

  1. Jan 6, 2014 #1

    harleysilo

    harleysilo

    harleysilo

    Well-Known Member

    Joined:
    Jul 7, 2006
    Messages:
    61
    Likes Received:
    0
    As a trial run to finishing my basement floor, i tried doing the garage floor. It cost me about $1.25 per foot, rental and supplies.

    The pictures don't capture exactly how it looks in real life, but close enough.

    I rented a concrete prep floor sander from HD, and used a concrete prep head on it. I followed that up with two grades of sandpaper, so my work stopped at like 30 or 60 grit.

    Once i got used to operating it and keeping it under control it went pretty well. I was shocked at the amount of dust i created, over 100 lbs. It took up the cream (top level of concrete, very fine, and exposed the aggregate). The sanding discs sanded down the gravel to some extent, but they did remove more concrete in the process, so the aggregate is every so slightly exposed. Walking barefeet the floor feels smooth. But close inspection on hand and knees reveals the result.

    I then stained it with H&C stain from Sherwin Williams, and followed that up with their Oil based Glossy Concrete sealer, bout 5 thin coats.

    The staining process revealed the areas that would accept stain, the white shapes. The sealer revealed the areas of differing fineness of sanded finish. I was not able to get the entire floor to the same level of luster.

    I'm going to do my basement in this manner, but i'm going to rent a better (i think) machine from Sunbelt rentals. If i have a bunch of random shapes show up in the basement, i may try cleaning those areas, but i may leave them, Up for suggestions on that issue.

    I'll also use a different sealing product, the oil based one for the garage stunk to high heaven, no way i can use that for days on end in my house.

    Here are a few pics, more to come.

    [​IMG]



    [​IMG]


    [​IMG]


    [​IMG]
     
  2. Jan 6, 2014 #2

    harleysilo

    harleysilo

    harleysilo

    Well-Known Member

    Joined:
    Jul 7, 2006
    Messages:
    61
    Likes Received:
    0
    [​IMG]

    That's the first layer of sealer going on.

    I talked with a professional regarding him doing my basement floor. He had several comments...

    If i envisioned a mirror smooth finish, i could forget about that idea. My floor was hand troweled in the 80's. If you shine a flashlight across it you will see many rises and dips. He implied that he could not grind if flat, and could not achieve what they have in say Home Depot, or a fancy trendy restaurant.

    I think he could do better than what i did on the garage, but am not sure the cost difference would be worth it.

    I need advice on the final finish too (if i do a sealer), as the choice for the garage floor may not have been the best, every dusty foot print shows up, and does not sweep away, you have mop it. The sealer could still be drying as it's been in the 50's in the garage, or it could just be the gloss finish, and maybe in the basement i need one not so wet glossy looking.

    The various shines you seen in the picture above are representative of the finished look, where the concrete was dense and sanded smooth it's glossy, where it is more porous with aggregate exposed it is duller.
     
  3. Jan 7, 2014 #3

    nealtw

    nealtw

    nealtw

    Contractor retired

    Joined:
    Nov 4, 2010
    Messages:
    23,897
    Likes Received:
    3,118
    I can't answer your questions but I have used both that smelly sealer and the water based stuff both made by the same people. The water based stuff seems to stand up just as good and we added colour to them too.
     

Share This Page