Replacing Old Fluorescent Light Ballasts with New Ballasts

Discussion in 'Electrical and Wiring' started by 1victorianfarmhouse, Feb 15, 2014.

  1. Feb 15, 2014 #1

    1victorianfarmhouse

    1victorianfarmhouse

    1victorianfarmhouse

    Established Member

    Joined:
    Feb 6, 2010
    Messages:
    225
    Likes Received:
    14
    I have an old fluorescent light in my basement that doesn't work. I've tried replacing both 4' bulbs, and both starters with no luck. The Starring and Co. ballast is dated Jan 9, 1957, and has some sticky stuff oozing out of it and has an old electrical smell. I'm guessing this might be the culprit..... The other light in the system works fine.

    On the left side it has a black wire and a black/white wire, and is marked LINE and Lights 1&2. One the right side is marked Lamp #1 and Lamp #2, with a black wire and a black/red wire.

    My question is to install the new ballast, is all I need to do is just connect the existing black and white wires to the new ballast, and the new blue and red wires as shown in the diagram on the new ballast in the photo? No starters needed?

    Photo of old and new ballasts attached.

    OF COURSE I will shut off the appropriate breaker before doing anything!

    Thanks!

    vince

    Ballasts.jpg
     
    Last edited: Feb 15, 2014
  2. Feb 15, 2014 #2

    nealtw

    nealtw

    nealtw

    Contractor retired

    Joined:
    Nov 4, 2010
    Messages:
    23,887
    Likes Received:
    3,114
  3. Feb 15, 2014 #3

    JoeD

    JoeD

    JoeD

    Well-Known Member

    Joined:
    Mar 16, 2006
    Messages:
    1,524
    Likes Received:
    272
    Yes. Wire like the diagram on the ballast.
     
  4. Feb 15, 2014 #4

    kok328

    kok328

    kok328

    Well-Known Member

    Joined:
    Nov 20, 2007
    Messages:
    2,755
    Likes Received:
    249
    Check around, it might be easier and cheaper to replace the entire fixture.
     
  5. Feb 15, 2014 #5

    1victorianfarmhouse

    1victorianfarmhouse

    1victorianfarmhouse

    Established Member

    Joined:
    Feb 6, 2010
    Messages:
    225
    Likes Received:
    14
    Thanks, Neal....yah, there might be some PCBs involved, will need to check the other two sets too, though they work.

    And thank you Joe, as well. With stuff like this I don't like to play trial and error even though it looks simple.

    vince
     
  6. Feb 15, 2014 #6

    1victorianfarmhouse

    1victorianfarmhouse

    1victorianfarmhouse

    Established Member

    Joined:
    Feb 6, 2010
    Messages:
    225
    Likes Received:
    14
    Thanks, kok, I already bought the ballasts a while ago, so I'm stuck with them. The old light fixtures are fine, and anything new would require redoing the mounting. I am planning to buy another new pair to add some additional light on the other side of the room, though.

    vince
     
  7. Feb 15, 2014 #7

    speedy petey

    speedy petey

    speedy petey

    Lic.Electrical Contractor

    Joined:
    Mar 15, 2006
    Messages:
    470
    Likes Received:
    44
    You will definitely have to re-wire the whole fixture. Most likely this fixture has starters that will have to be eliminated. Sometimes it can look complicated, but every wire is shown in the diagram on the ballast so if you take your time you should be able to figure it out.
     
  8. Feb 15, 2014 #8

    Wuzzat?

    Wuzzat?

    Wuzzat?

    Well-Known Member Sponsor

    Joined:
    Jan 20, 2010
    Messages:
    2,471
    Likes Received:
    175
    If the fixture is not grounded it probably won't work reliably. There is capacitance between the tubes and the metal housing and this is necessary for the tubes to "start".

    Match the tubes to the ballast.

    There is a small chance that the fixture still won't work with a new ballast and tubes. In this case there is a bad connection or broken wire.

    I doubt the new ballast will last 57 years, regardless of what the GE's computer projections say.
     
    Last edited: Feb 15, 2014

Share This Page